gpi-prototype-top-banner

News (931)

Precise control over hot runner temperatures was the key to ending a problem with burned parts that plagued a particular job being run by custom molder American Plastic Molding Corporation (APM), enabling the company to increase output of saleable product by 10 to 15%.
 
The part discoloration caused by burning stopped almost immediately after connecting an Ion Series temperature controller from Fast Heat Inc. to a 16-cavity hot runner system that was producing 30% glass-filled nylon 6.6 parts for a Tier 1 supplier to the automotive industry, according to Alan Myers, APM plant manager. Within two hours after installing the controller, APM had fine-tuned the system to the point where temperatures were reduced by nearly 70 ºF.  
 
“Before we installed the Fast Heat controller, we were unable to reduce the temperature without having gates freeze,” said Myers, “but within the first couple of hours, it became a question of ‘How low can the temperature go?’ We soon established a new temperature range of 430 to 440 ºF. The lower temperatures increased our output of good parts by 10 to 15% and eliminated the labor involved in sorting out parts that were burned.”
 
Fast Heat’s Ion Series controller has also increased productivity in other ways, according to Myers. In startups it quickly tunes the system to the new set of molding parameters. And in the event of a zone shutdown caused, for example, by a heater failure, the controller automatically slaves the affected cavity to another cavity, running two cavities from the thermocouple in the unaffected one.
 
“In the past, when a zone shut down, we would end up producing from 15 cavities instead of 16, making that much less product during the typical three-day turnaround needed to replace the defective unit,” said Myers.
 
Family-owned and -operated since it was founded in 1971, APM is a full-service custom molder that provides extensive engineering services and stages free quarterly seminars on design and engineering for customers and prospects. The company has 38 injection molding machines, an assembly facility with lean manufacturing cells, an on-site mold shop, and a 60,000 sq.ft. (5,575 sq,m) warehouse. It provides full engineering services and offers customers supply chain sourcing and management, warehousing, and distribution. Employing 120 people, APM serves customers in a wide range of end use industries.   

For more information, visit: www.apmc.com

Tuesday, 31 July 2012 11:02

SIGGRAPH 2012 Business Symposium

Written by

In its second year, the SIGGRAPH Business Symposium provides an intimate, interactive forum for open, frank conversations among leaders and executives in the visual effects, gaming, and media arenas as they explore the present and future of the industry. SIGGRAPH 2012 welcomes visionary leaders and experts from a broad spectrum of the computer graphics industry, including animation, education, motion pictures, gaming, and visual effects, to this year’s Business Symposium in Los Angeles, 5 August 2012.

This full-day event is an exclusive opportunity for attendees to gain high-level, experiential vantage point insight from the producers and executives who have all forged unique paths to their current roles and now design the industry’s direction. The day begins with breakfast and round-table discussions of the day's agenda. Possible topics include visual-effects production, marketing, international law, education, business development, and other areas related to the industry's current issues. The morning session provides a foundation for the day – an opportunity to hear from leaders on the global stage what they experience from their particular perspective, followed by featured speakers Carl Rosendahl and John Textor, both visionary leaders who influence the direction of our industry in vastly different manners.

Throughout the day attendees will join in-depth discussion and have ample time to interact with their peers before the afternoon session closes. The Symposium provides a look into newer business models from some of the people and companies defining the future.

SIGGRAPH 2012 will bring thousands of computer graphics and interactive technology professionals from six continents to Los Angeles, California for the industry's most respected technical and creative programs focusing on research, science, art, animation, music, gaming, interactivity, education, and the web from Sunday, 5 August through Thursday, 9 August 2012 at the Los Angeles Convention Center. SIGGRAPH 2012 includes a three-day exhibition of products and services from the computer graphics and interactive marketplace from 7-9 August 2012. More details are available at SIGGRAPH 2012 or on  Facebook and Twitter.

For more information, visit: s2012.siggraph.org

HTI Plastics made a significant investment this year by purchasing two Krauss Maffei EX Series machines. These machines are all electric with a fast response, direct force transmission and a closed system ensuring absolute cleanliness.  Staying ahead of the competition and utilizing the latest technology has always been our goal at HTI Plastics.

One of HTI’s machines, the 150 ton model, was displayed in Krauss Maffei’s exhibit during the NPE 2012 this past April in Orlando Florida. The machine was shipped from Germany to Orlando, Florida then made its way to Lincoln, Nebraska.

“We are pleased with the new presses and feel it will keep us a step ahead of our competitors and will ultimately lead to better service for our customers and higher precision in the molding of their products and components,” stated Troy Just, division president.

In addition to the new machines, HTI Plastics enhanced its design and engineering capabilities with the addition of simulation software which tests customers’ product designs in real-world environments before manufacture.  This will benefit customers by reducing time to market and the number of prototypes needed before going into production.

As a division of PCE Inc., HTI Plastics benefits from the corporate commitment to capital investments in injection molding equipment that help maintain high product quality, while improving efficiencies and reducing energy consumption.

For more information, visit: www.htiplastic.com

Imagine being able to design a new aircraft engine part on a computer, and then being able to print it. Not the design – the actual part. And not just a lightweight, nonfunctional model, but an actual working part to be installed in an engine.

The University of Dayton Research Institute was awarded $3 million from the Ohio Third Frontier to provide specialized materials for use in additive manufacturing – the science of using computer printers to create three-dimensional, functional objects. The University of Dayton Research Institute will work with program partners, Stratasys of Eden Prairie, Minn., and PolyOne and Rapid Prototype Plus Manufacturing Inc. (RP+M) of Avon Lake, Ohio, to develop aircraft-engine components for GE Aviation – who also collaborated on the program proposal – as well as parts and components for ATK Aerospace Structures, Boeing, Goodrich, Honda, Lockheed Martin and Northrop Grumman.

While traditional paper printers use a moving toner cartridge head to form lines of text, adding row upon row of toner as the paper moves through the printer, 3-D printing works much the same way. Instead of toner, however, a free-moving printer head precisely deposits layer upon layer of plastic or other material to create a solid object from the bottom up.

3-D printing technology has existed for about 20 years, but additive manufacturing in its current form is only about five years old, said Brian Rice, head of the Research Institute's Multi-Scale Composites and Polymers Division and program lead for the Third Frontier-funded Advanced Materials for Additive Manufacturing Maturation program.

"The difference is that 3-D printing is known in the industry as being used for nonfunctional prototypes or models, while additive manufacturing is being used to create usable parts for industries such as aerospace, energy, medical and consumer products," Rice said.

Additive manufacturing, which made headlines this month in the Wall Street Journal and USA Today and was named number one in Aviation Week & Space Technology magazine's May list of "Top Technologies to Watch," is a rapidly growing manufacturing technology being touted for its cost savings and waste reduction. By 2015, the sale of additive manufacturing products and services worldwide is expected to grow to $3.7 billion from $1.71 billion in 2011, according to independent consultants Wohlers Associates.

There are a number of advantages to additive manufacturing over traditional manufacturing, such as injection molding or machining, Rice said.

"Cost savings is a major benefit, because there are no molds or tooling needed to fabricate parts. With traditional manufacturing, every time you want to make even a slight change to the design of what you are making, you have to retool or make an entirely new mold, and that gets very expensive. With additive manufacturing, you can change your design as often as you want simply by changing the design on your computer file. "You can't make complex parts with injection molding," Rice added. "And because you can print an entire part in one piece with additive manufacturing, instead of welding or attaching separate components together as in traditional manufacturing, the finished part is stronger."

Additive manufacturing holds additional benefits, said Jeff DeGrange, vice-president of Stratasys, which owns an industrial line of additive manufacturing machines that will be used to print components for end users.

"It's better for the environment because it reduces waste," DeGrange said. "With additive manufacturing, you only use as much material as you need for the part you're printing. But with machining, you're shaping objects by removing material from a larger block until you have the desired form, so there is a good bit of wasted material."

Additive manufacturing eliminates the need for bolts, screws and welding and, in some cases, reinforced polymers can be used to replace heavier materials, DeGrange added.

"Lighter parts mean greater fuel efficiency in vehicles and aircraft that use them. Another advantage is the cost savings that comes from a print-as-needed process, because you don't need to ship parts or find a place to warehouse them," he said.

3-D printers can use polymer, metal or ceramic feedstock, but our focus will be on polymers, which is already a major manufacturing industry in Ohio, according to Rice.

"UDRI has developed a highly specialized nanomaterial that will reinforce the polymer feedstock, giving the finished product greater strength and stiffness than nonreinforced polymer. It will also make the polymer electrically conductive," he said.

PolyOne will scale-up the polymer feedstock needed for mass manufacturing, Stratasys will support the inclusion of new materials in their additive manufacturing systems, and RP+M will use its expertise in additive parts manufacturing to work with Stratasys to print and supply parts to end users, Rice said.

"We've created an entire supply chain designed to create Ohio jobs," Rice said. "We expect this program to result in the creation of 30 high-tech jobs in Ohio during the first three years and 85 jobs after five years."

The Research Institute will use part of the Third Frontier award to purchase a 3-D printer to demonstrate the technology, and the University of Dayton School of Engineering, which recently purchased a similar machine, will provide hands-on opportunities for engineering students to become involved.

"They will focus on research into new materials and innovation in additive manufacturing," Rice said. "It's a boost for our program, and it will also provide those students with skills that will help them secure high-tech manufacturing jobs after graduation."

For more information, visit: www.udayton.edu

UL, a world leader in advancing safety, announced today the acquisition of Laramie, Wyoming-based IDES, the leading informational resource for plastic material.  Coinciding with the announcement, UL unveiled the next-generation version of IDES' popular Prospector online service which combines plastic materials data sheets and UL plastic identification reports within a single searchable interface.

IDES Prospector is the industry standard for plastic material specification, relied upon by 319,000 design engineers and processors to streamline polymers selection.  Specifiers for plastic materials can now visit IDES.com to find all crucial polymer data sheet and UL verified data in one place, featuring the easy-to-use search, comparison and navigation functionality that Prospector users expect.

Search queries and results now include data from UL's plastics recognition yellow cards, featuring materials attributes independently verified from small scale flammability and ignition, mechanical, electrical, and short term thermal tests.  More than 60,000 different plastic materials have yellow cards, which are trusted by product makers and specifiers for qualification.

"We're thrilled to add the talented IDES team and industry-leading information technology," said Sara Greenstein, senior vice president of UL.  "The Prospector tool gives UL a dynamic medium for converting our data into accessible intelligence that can inform and speed decisions throughout the plastics supply chain."

"For our people and our customers, this is an exciting combination that is bearing fruit already," said Mike Kmetz, managing director of IDES.  "Our Prospector upgrade as part of UL is a tremendous milestone - the first of many more to come."

While yellow cards can still be found at ULiQ, UL IDES Prospector will eventually become the exclusive resource for yellow card information.  ULiQ remains the destination for UL list searches in other product categories, including appliance wiring materials, printed wiring boards, switches, electrical insulation systems and restricted substances.

IDES is the world's leading informational resource for plastic material, based in Laramie, Wyoming.  IDES provides plastic materials information and data sheets in Prospector, an online searchable data sheet catalog of plastic materials properties, relied upon by more than 319,000 industry users worldwide.

For more information, visit: www.IDES.com

Wednesday, 25 July 2012 09:53

GW Silicones Expansion Completed

Written by

GW Silicones announced today the completion of its new facility at the GW Plastics Technical Campus in Royalton, Vermont. The $3.5 million expansion, which began in the fall of 2011, includes a 15,000 square foot expansion that is scalable to 25,000 square feet. The new state-of-the-art Liquid Silicone Rubber (LSR) molding and assembly facility is capable of supporting up to 18 new injection machines and features an ISO Class 8 cleanroom along with expanded office, engineering and conference space.

“Our customers are increasingly looking to silicone as an alternative to thermoplastic because of its unique biocompatibility and performance attributes – it is odorless, tasteless, stainless, bacteria-resistant, easy to clean and sterilize, and works extremely well in complex injection molding applications with extremely fine detail and very tight tolerances,” explains Terri Marion, GW Silicones Business Development Manager. “The expansion of GW Silicones reflects our commitment to meeting our customers’ growing demand for cutting-edge silicone applications in the medical device/healthcare and automotive markets.”

GW Silicones, a division of GW Plastics, delivers cost-effective solutions for the complex molding and manufacture of liquid silicone rubber (LSR) and unique multi-material components and assemblies to the medical device/healthcare market. GW Silicones specializes in product design and development, in-house precision tooling, and scientific injection molding along with a variety of contract manufacturing services. “With the recent expansion of our manufacturing facility in Royalton, VT, we can now offer improved production scalability along with our world class speed to market, quality and delivery,” said Mark Hammond, General Manager of GW Silicones.

For more information, visit: www.gwplastics.com/en

The Hamburg-based software company Simufact Engineering now offers new versions of its simulation software Simufact.forming and Simufact.welding. Providing more functionality for a broader scope of application while offering a simplified usability - that´s the credo of the new software versions that are employed for the design and optimization of manufacturing techniques in metal processing.

With the new Simufact software releases, companies aiming to link various production processes in the process chain (from semi-finished material to finished component) have come closer to their goal of an integrated, cross-process approach in the simulation of entire process chains.

Simufact simulation solutions cover all essential production processes from forging to cold massive forming, rolling, sheet metal forming, mechanical joining, heat treatment, and welding. Also, standard interfaces allow customers a fast and reliable integration of Simufact software in their CAD/CAE environments.

A major step forward is Simufact’s integration of material data in the simulation of forming and joining processes: Simufact.forming 11 and Simufact.welding 3.1 not only offer a multitude of new, experimental material data; they also provide access to high quality analytical material data, thus ensuring accurate simulation results.
 
Simufact.forming 11 – professional forming simulation

Simufact.forming is an established simulation solution for forming and joining processes. The software release Simufact.forming 11 includes new modules for open die forging and ring rolling. Application-specific functionalities such as fully automated processing of a complete pass schedule in open die or radial forging, and the consideration of the manufacturer’s kinematic concepts in ring rolling, help the user to model and simulate all possible processes and conditions of these production processes.

Thanks to new possibilities in result-dependant, force and path controlled processing as well as an optional, method-related calculation of the structural transformation during forging, these new special modules have become indispensable tools for companies that use ring rolling and open die forging.

Release 11 is particularly interesting for joining experts, since it takes adhesives and high speed effects into consideration, which are gaining more importance in modern joining technology.

By offering improved possibilities for networking and evaluation, Simufact.forming 11 eases the engineer’s daily work in tool and process development. The feature “optimization” allows the comfortable testing of process options and ensures substantial time savings for the definition of the best process design. Highlights include the flexible description of thermo-physical boundary and initial conditions, and the automated reporting in pre- and post-processing.

The efficient simulation of realistic heat-treatment processes provides for more flexibility and realism in mapping the process chain – before, during, and after the forming process.
 
Simufact.welding 3.1 – more than welding simulation

Simufact.welding 3.1 enables the simulation of various welding methods. Cutting edge solver technology and a user friendly overall concept allow for an effective calculation of welding sequences and a realistic prediction of component distortion, also taking into account microstructural transformations.

The coupling of Simufact.welding with Simufact.forming is a new functionality linking different process chains. Thus, processes taking place before or after welding can be efficiently integrated in the numerical approach. Easy data transfer allows for consideration of the forming history and the strength analyses of the simulated welding seams.

The calculation of phase transformation and phase volume fractions, as well as the automatic mapping of weld filler metals complement the new features. Simufact.welding 3.1 provides the user with a simple and comfortable modelling of more complex welding seams, even the simulation of multi-layer welding is now possible. Last but not least, the new release offers an improved calculation of contacts for process related gap formation during the welding process.

For more information, visit: www.simufact.com

The DeLaMare Science and Engineering Library at the University of Nevada, Reno is the first academic library in the United States to make the leap to offer 3D printing and scanning as a library service to all students, enabling students in a multitude of disciplines to make plastic 3D models from a computer drawing for their research and studies.

“We’ve brought the technology out of the lab and into access for all students,” Tod Colegrove, director of the DeLaMare library, said. “It’s a first for universities around the country where the machines are typically part of a specialized program or research lab.”

Using specialized software, the machine can build a three-dimensional, real world plastic model from a computerized drawing of an object. It can be as simple as a box or as complex as a protein chain from a theoretical model. The model can be inspected, modifications can be made in the drawing and another prototype printed.

“3D printers are typically purchased by a faculty member with grant funds in support of a particular research project, and installed in isolated departmental locations,” Colegrove said. “Printers remain largely inaccessible to students and faculty outside of a select few. We’ve changed that.”

“In the arts, sciences and engineering, breakthroughs in learning or research often require going beyond pencil and paper,” he said. “With technology and a supportive environment, it becomes possible to breathe life into ideas – in the library. We have a waiting list for projects, which can take anywhere from 40 minutes to 40 hours, depending on the complexity.

“Our first job – a rotor for an impeller pump being prototyped by a team of senior engineering students – came in literally as we were pulling the printer out of the box. The machines haven’t stopped running since.”

University students are using the 3D printing service to “print” custom parts for student-designed robots and hovercraft, fine art sculpture, chemical models, lattice structures, a moving parts engine block and more. The potential for prototyping models and experimental apparatus in support of ongoing research has become a reality for many students who lacked access or the funds to send the project out to a commercial 3D print company.

“This service leverages library access with an incredible new opportunity for student engagement,” Colegrove said. “It takes the library’s support of the learning and research missions of the University to a new level – beyond simple information exchange and consumption into knowledge-driven creation.”

For more information, visit: www.unr.edu

Thursday, 19 July 2012 09:28

Morris Technologies Acquires Five-Axis Mill

Written by

Morris Technologies, Inc. (MTI), a service provider specializing in additive manufacturing and CNC machining, has acquired a DMU 50 five-axis machine from Mori Seiki.  The DMU 50 machine is a state-of-the-art mill that features a performance-enhancing NC swivel rotary table, high rigidity, and a large bearing diameter in the B- and C-axis.  The equipment is the latest addition to MTI's world-class machine shop.

A five-axis machining center utilizes two axes in addition to the standard three axes (X/Y/Z), so the tool can move along five different planes. This allows the part to be fixtured just once as the tools and the table rotate according to the CNC specifications.  The result is parts that are produced with high precision and detail and tight tolerances.

Morris Technologies will utilize the DMU 50 machine to produce complex parts for the medical, aerospace, and other industries.  The new mill enhances the company's machining capabilities, which also includes EDM and Swiss turn.

Adam Collins, machining manager, believes this acquisition takes Morris Technologies to a new level.  "Until now, we've had a very complete shop, but the one missing piece of the puzzle was a five-axis (machine)," says Collins.  "We now have a facility that rivals others in the industry.  This is really exciting for us."

As the global leader in additive metal manufacturing, Morris Technologies also will use the five-axis machine to complement the company's extensive additive manufacturing capabilities.

Based in Cincinnati, Ohio, Morris Technologies, Inc. (MTI) has been on the cutting edge of manufacturing technologies since 1994.  MTI's heavy investment in research and development has enabled them to evolve into the global leader in additive-metal manufacturing processes and advance technologies by offering new materials and developing new hardware.  MTI also specializes in end-to-end product development, from engineering to prototyping to low-volume manufacturing.

For more information, visit: www.morristech.com or www.dmgmoriseikiusa.com/five-axis-dmu-series/dmu-50

Barnes Group Inc. (NYSE:B), an international aerospace and industrial manufacturing and service provider, today announced that it has entered into a definitive agreement to acquire privately held Synventive Molding Solutions, a leading designer and manufacturer of highly engineered and customized hot runner systems, components, and services, headquartered in Peabody, Massachusetts. Hot runner systems are the enabling technology for many complex injection molding applications and are standard in industries that require premium product aesthetics and performance.

Barnes Group has agreed to purchase all the capital stock of Synventive for $335 million in cash, subject to certain closing and post-closing adjustments, and is expected to finance the transaction with cash on hand and additional borrowings under an accordion feature of the Company’s existing credit agreement. The acquisition is anticipated to close in August 2012, subject to the receipt of regulatory approvals and the satisfaction of other closing conditions, including obtaining necessary third party agreements.

Synventive is one of the world’s largest hot runner systems manufacturers, serving a global customer base of more than 3,000 molders, mold makers and original equipment manufacturers across 50 countries. With estimated 2012 revenues of approximately $160 million, Synventive operates out of three manufacturing locations in the United States, Germany and China, with sales and service offices in 28 countries and 770 employees worldwide. Synventive will operate as a strategic business unit within Barnes Group’s Industrial Segment.

“We are very excited to add Synventive to Barnes Group and about the tremendous opportunities for growth we expect this acquisition to bring to us,” said Gregory Milzcik, President and CEO of Barnes Group Inc. “The global demand for more complex, highly technical injection molding solutions is anticipated to grow substantially in the future. We are eager to add Synventive’s innovative products and services to Barnes Group’s core manufacturing capabilities and to work with them to create a stronger, more dynamic presence in the global marketplace.”

Added Milzcik, “Barnes Group takes pride in providing rewarding opportunities for all employees to grow and develop their careers with the company. We are impressed with the expertise and commitment demonstrated at Synventive and are enthusiastic about having their employees join our team and contribute to our ongoing success. We welcome the opportunity to invest in this outstanding company and to continue providing customers with the superior products and services associated with the Barnes Group and Synventive names.”

Barnes Group will provide additional details about the Synventive business on its second quarter 2012 earnings call scheduled for July 27, 2012 at 8:30 a.m.

For more information, visit: www.BGInc.com or www.synventive.com

Morris Great Lakes, a division of Morris Group, Inc., broke ground for a new headquarters in Cranberry Township, Pennsylvania on July 3.  Morris Great Lakes supplies advanced machine tools and related engineering, technology, and support services to manufacturers of precision machined parts in western Pennsylvania, western New York, and the state of West Virginia.

After reviewing several alternative locations in Pennsylvania and New York, Corey Johnson, President of Morris Great Lakes, chose to keep the company’s headquarters in Butler County.

“We’re very pleased to be staying in Cranberry Township,” states Johnson. “It’s been home to us for almost ten years and after a lengthy search process, we decided that this was the best place for us to build. The location is central to our regional customer base. We’re not only excited about our expanded, new headquarters; we’re excited about helping the area grow.”

The 12,000 square-foot facility will include an 8,000 square-foot state-of-the-art technical center housing machine demonstration areas and test-cutting or trial areas devoted to developing custom turnkey and automated manufacturing solutions for customers. The remaining square footage will be reserved for application engineering, parts, service, and administrative offices. W.K. Thomas and Associates of Butler, Pennsylvania was selected to construct the facility, due to open in December 2012.

Morris Great Lakes currently employs 35 people. It is the exclusive regional distributor of Okuma, Tsugami, Hardinge, and Bridgeport CNC machine tools. In addition to new machine tools, Morris Great Lakes provides engineered solutions, replacement parts, service, preventive maintenance and other services including customer consultation, financing, installation, training, and disposition of retired machines.  Its customers are manufacturers of precision machined parts from virtually every industry, including aerospace, medical, automotive, and heavy industries.

Morris Great Lakes is a division of Morris Group, Inc. whose history of serving the manufacturing community dates back to 1941. Its thirteen divisions form one of the largest machine tool distribution networks in North America. The firm is headquartered in Windsor, Connecticut and employs more than 400.

For more information, visit: www.morrisgreatlakes.com

InventHelp, America’s largest inventor service company, has launched a new website this week to highlight the company’s inventor services and continue to offer resources to inventors.

InventHelp®, known for iconic commercials featuring the prehistoric InventHelp caveman chipping at the wheel, is excited to launch a more user- and inventor-friendly site. “Our site is already known as a resource for inventors, but now it’s easier to use and has a great new look,” said InventHelp® President Robert Susa.

The new website features client inventor stories and testimonial videos, access to blogs and details about InventHelp’s partnerships with organizations like the Electronic Retailing Association. The site also features a section on INPEX®, the largest trade show in the United States for inventors, which InventHelp® sponsors.

Inventors can use the site to locate the closest InventHelp® sales office in the area, as well as read more about the services the company offers. Additionally, there is a section of the site designed specifically for companies that are seeking new products for license or manufacture. Companies interested in seeing clients’ inventions and new products can register on the site for the InventHelp® Data Bank at no charge.

The redesigned website also directs consumers looking to purchase new products to the official InventHelp Store, a website that showcases innovative new products invented by InventHelp clients.         

In business since 1984, InventHelp® is America’s largest inventor service company, with more than 60 sales offices in the U.S., Canada and abroad. InventHelp® also holds INPEX®, America’s Largest Invention Show.

For more information, visit: www.inventhelp.com

Green developer Voltaic Solaire will unveil the first building in New York City to power itself. The mixed-use private development, known as the Delta*, was built in conjunction with IKEA, Samsung, Sharp, and other partners. It combines solar and wind energy to meet 100% of its energy needs—generating its own electricity, hot water and heat. “The Delta fulfills the promise of Mayor Bloomberg’s PlaNYC, whose goal is to reduce New York's carbon emissions by 30% by 2030,” says Voltaic Solaire CFO Ron Faia.

From its solar panels to its solar skin, from its aggregate building materials to its innovative window treatments, the Delta is a case study in sustainability and energy independence. Renewable energy is projected to see 40% growth per year for the foreseeable future. Below are a number of Voltaic Solaire’s partners who have been integral in supplying the Delta with products and materials to make the project possible.

IKEA
Staged from top to toe in sleek, economical furniture, the Delta proves that high design and efficiency can work hand in glove. For Swedish furniture makers Ikea, it’s about taking care of people and the planet—from tackling the problem of child poverty to creating renewable energy. One can see evidence of this work through innovative IKEA products and solutions throughout the Delta. Believing as they do that if we all take small actions, we can all contribute to big results, Ikea has proven a perfect fit for this project.

Sharp
Since 1959, Sharp has led the solar electric industry with efficient solar systems, from the world's first solar-powered calculator to solar-powered residential and commercial applications. Now the company partners with SMBs such as Voltaic Solaire in truly revolutionary developments. As founder Tokuji Hayakawa notes, "If we could find a way of generating electricity from limitless solar heat and light, that would benefit humankind to an extent we can scarcely imagine."

Samsung
The Delta’s additional solar modules were supplied by Samsung. The company’s worldwide presence adds heft to the Delta project, with its history of stability and reliability. In addition to their core business around LCD and semiconductor manufacturing, Samsung is making a name in the solar energy space. The company has demonstrated its long-term commitment backed by financial strength, as well as a high customer satisfaction rating.

Kingston Block
The Delta is composed of green and recycled materials, including aggregate cement and bricks. Kingston Block & Masonry Supply, LLC, an innovator in the concrete and masonry industries, have taken a leadership role in manufacturing a sustainable line of concrete products. With global concern for sustainable building on the rise, the company understands the importance of reducing our carbon footprint.

Eemax
Tankless water heaters are now essential for any truly sustainable project. Eemax’s water heaters offer 99% thermal energy efficiencies, paying for them-selves many times over, which was an enormous value-add for Voltaic Solaire. The original Eemax technology was patented and quickly emerged as the most flexible technology on the market, which was a critical factor in the early stages of the development of the U.S. market for electric tankless heaters.

* The Delta is on the forefront of a sustainable movement that is long overdue in New York and other dense urban areas. The building is comprised of one triplex residence and one studio residence, with attached restaurant and retail. It will be maintained as a bed and breakfast, in order to facilitate ongoing educational visits for schools, tour groups, et. al., underlining Voltaic Solaire’s ethos of philanthropy and sustainability.

For more information, visit: www.voltaicsolaire.com

Thursday, 12 July 2012 09:05

IHS Acquires Invention Machine

Written by

IHS Inc. (NYSE:IHS), the leading global source of information and analysis, has acquired Invention Machine for approximately $40 million. Invention Machine is a leader in semantic search technology that uncovers relevant insights held within a wealth of internal and external knowledge sources, transforming the underlying data into actionable intelligence. Their patented semantic question-answering software engine leads engineers and knowledge workers to information quickly and enables them to rapidly digest it to make better decisions.

As previously announced, IHS also has completed the closing of its acquisition of GlobalSpec Inc., from Warburg Pincus LLC for $135 million. GlobalSpec is the leading specialized vertical search, product information and global access point providing critical digital information tied to key Product Engineering and Design workflows for seven million engineers.

“The acquisitions of Invention Machine and GlobalSpec present a unique opportunity for IHS to transform our existing engineering specifications and standards business to long-term double-digit growth, and accelerate the IHS Product Design business by increasing the value we offer to engineers, researchers and scientists by connecting innovation to knowledge workers,” said Jerre Stead, IHS chairman and chief executive officer. “With Invention Machine’s Goldfire as the front-end, we will bring together all IHS content, insight and tools into an innovative solution that will address many of the unsolved problems facing engineers. This will enable greater productivity, accuracy and design quality, and help customers accelerate innovation and deliver superior products and services.”

Invention Machine’s Goldfire product is the decision engine built on top of a patented semantic search engine that connects engineers and innovation and knowledge workers, on-demand, to one another and to the internal and external knowledge and trends needed to develop, maintain and produce breakthrough products and services. Semantic search engines understand the meanings and relationships of words, and can provide more relevant results than traditional text-based search engines.

IHS President and Chief Operating Officer Scott Key said: “Invention Machine is an excellent strategic fit for IHS and is a critical component of the evolution and transformation of the Product Design business. Invention Machine provides a software tool that lays on top of IHS and GlobalSpec content, as well as a customer’s own internal and external content, to enable customers to rapidly digest information and make better decisions.

“The acquisitions will allow IHS to provide a revolutionary knowledge management solution that will seamlessly access IHS products, external content and a customer’s internal information. It gives us the opportunity to further expand within target customers by creating new products for quality, standards applicability and knowledge management.”

Headquartered in Boston, Invention Machine employs approximately 100 people and also has offices in: Minsk, Belarus; London; Frankfurt; Paris, and Tokyo.

For more information, visit: www.ihs.com or www.inventionmachine.com

At Farnborough Airshow, EADS Innovation Works is presenting the prototype of a portable Unmanned Aerial Vehicle (UAV) produced by Additive Layer Manufacturing (ALM) technology, also known as 3D-printing. The plane with a wingspan of approximately. 1.5 meters has been designed by students from the University of Leeds. The small, portable drone will be capable of being controlled via wireless video communication over a short distance. Powered by batteries, it could serve as a tool for surveillance, search and rescue or disaster control.

Using ALM technology in the production of such a small drone opens new possibilities for aerodynamic optimizations such as wing twist, which would otherwise be difficult and expensive to realize for an aircraft of this scale. Different, detachable wings can be “printed” in a relatively short time to adapt the UAV to missions with different requirements.

The four students from the University of Leeds’ Faculty of Engineering have developed an initial concept of the UAV, created the design and performed an aerodynamic analysis under the supervision of EADS expert Martin Muir. In order to take advantage of the ALM technology the students carried out a detailed design of the wing through topology and aerodynamic optimisation. This allows building a pair of wings which are optimised in terms of weight, aerodynamics and stability and yet cheap to produce. Thanks to the tests performed, both the angle of incidence and the angle of twist could be optimized. Normally, manufacturing of such complex parts would be too expensive for a small UAV. With ALM, it is possible to produce several sets of – for example – wings tailor made for different missions at a reasonable price.

The students also performed a stability and control analysis of the whole system and produced assembly instructions for the print shop. A flight capable metallic version will be manufactured at EADS Innovation Works UK ALM facilities in Filton. This plane will be produced using innovative Direct Metal Laser Sintering (DMLS) technology. The plastic material UAV shown at Farnborough serves only for exhibition purposes and displays the design features made possible by ALM technology.

The UAV has been sized to take advantage of future propulsion systems, such as the Lightweight Hydrogen Fuel Cells (LwHFC) currently under development by EADS Innovation Works. A replacement of the existing battery system with the LwHFC would increase the endurance of the UAV from two hours of continuous flight, to approximately six hours. The sizing and optimisation of the UAV’s fuselage and wings was undertaken with the future use of LwHFCs in mind, hence the large open spaces and large profile wing.

The revolutionary manufacturing process known as Additive Layer Manufacturing (ALM) is based upon the principles of rapid prototyping and allows single products to be grown from a fine powder of metal (such as titanium, stainless steel or aluminium), nylon or carbon-reinforced plastics. EADS has developed the technology to the extent that it can manipulate metals, nylon, and carbon-reinforced plastics at a molecular level, which allows it to be applied to high-stress, safety critical aviation uses. Compared to a traditional, machined part, those produced by ALM are up to 65% lighter but still as strong as those would be. Simply put, a part is designed on a computer, which then directs a high-powered laser at material in powder form, melting it into a solid shape, repetitively, layer by layer, until the desired part is completed. The development of ALM is an activity that spans the entire EADS group, with early applications in the production of fixtures and tooling for Airbus, and flying applications being implemented by Eurocopter and Astrium. EADS’ UK research facilities have the lead in the group’s ALM activities.

Another piece of innovative ALM technology made in UK on display at the EADS’ stand is the Laminar Flow Device which can be mounted on the leading edge of an aircraft’s wing section. It enables laminar flow over large portions of a swept wing by removing the turbulent boundary layer of the attachment-line flow at the wing’s leading edge. Laminar flow causes less skin friction drag than turbulent flow and therefore helps to reduce fuel consumption.

ALM technology makes it possible to produce the complex contoured shape at a low cost. The device on the model on display at Farnborough is produced using the EADS proprietary ScalmalloyRP material, which provides exceptional mechanical properties useful in the production of complexly shaped structures.

For more information, visit: www.eads.com

For many years, A1 Technologies has been an active advocate for placing advanced, integrated 3D digital technologies into the hands of tomorrow’s designers, engineers and manufacturers to encourage and develop these skills for future generations. In April 2009 the company sold the world’s very first low-cost commercial 3D printer. Now, following stringent R&D efforts the company is delighted to be launching a brand new, proprietary 3D printer, the Maxit, with some key design and operational improvements.

The Maxit 3D printer has been developed to enable it to be built quickly and easily, within a few hours. A major part of the A1 mission is to engage children — in a school environment — to get creative with 3D printing and associated technologies, and to become familiar and comfortable with the technology. This is because A1 firmly believes that, in the future, we will all design+make in 3D, and putting 3D tools into classrooms now is the best investment we can make into that future for industry and for society.

What is more, reliable printing has also been at the heart of the development of the Maxit 3D printer, with quality electronic components sourced to support uninterrupted and consistent printing operations.  Thanks to a key design feature (the motor is remote from the hot end), the printing head is much lighter with lower inertia, allowing faster printing.

Maxit Specifications:

  • Dimensions 360 x 360 x 320 mm (excluding material holder)
  • Weight 2.7 kg
  • Printable area: 210 x 160 x 100 mm
  • Printing Speed: 40+ mm/sec
  • Layer thickness: 0.125 – 0.3 mm
  • Nozzle size: 0.5 mm (good for fast printing)
  • Filament size: 3 mm
  • Material: PLA (Poly Lactic Acid: biodegradable material)
  • Supplied complete with software
  • Maxit — At a glance
  • Super light and easy to transport
  • Very simple to assemble (under a day)
  • Reliable support
  • Compatible with CAD software — both open source and commercial
  • Price: £995

According to Martin Stevens, CEO at A1 Technologies: “3D Printing is proving to be a disruptive technology in many industrial sectors: however, it is also just on the verge of hitting mainstream consciousness and I believe that it is impossible to overstate just how important the technology will be in the future. That is why I am so passionate about getting 3D printing into classrooms now, to furnish kids with the knowledge and the skills to succeed in the future whether this is for their careers or as informed citizens. And, beyond that, hands-on learning with products such as these has been shown to foster enthusiasm for STEM subjects, not to mention entrepreneurial spirit.”

3D Printing, however, is not a process that can be utilised in isolation of other 3D disciplines. To this end, A1 Technologies offers a globally unique and compelling mix of low-cost 3D products, with complete integration to make 21st century engineering principles both accessible and applicable in the classroom. As well as 3D printing; 3D design, 3D scanning and 3D machining products can all be sourced from A1 Technologies to provide a fully comprehensive suite for designing and making in 3D.

For more information, visit: www.a1-tech.co.uk/maxit-3d-printer

MCAD Technologies, a SolidWorks reseller located in Lakewood, Colorado, purchased from Shounco Design Studios, Inc. the territorial rights for sales and support of SolidWorks in Oregon and Washington. This merger forms the MCAD Northwest division which will occupy the existing Shounco Design Studios’ office in Beaverton, Oregon.

MCAD Technologies was incorporated in 1989 with a mission to sell and support mechanical CAD, analysis and data management software to the Colorado marketplace. In 1997, MCAD became a SolidWorks value-added reseller for the Colorado Territory. With the recent merger, MCAD Technologies has offices in Colorado, Washington, New Mexico and now Oregon with territory rights in 5 states across the country.

MCAD and Shounco Design Studios, Inc. have developed very similar approaches to providing the highest quality technical support, training and sales to their respective regions and this made the merger a logical step for MCAD’s expansion plan. MCAD will be adding staff to the existing Shounco Design Studios, Inc. to better meet the needs of the growing Washington and Oregon engineering community.

"MCAD Technologies has demonstrated strong leadership in the channel since becoming a SolidWorks value-added reseller in 1997. They continue to provide excellent support and training for the entire SolidWorks application portfolio while delivering additional value for their customers. We are certain MCAD Technologies will provide a high level of support to the Northwest Territories and look forward to their success," said Alfred Saad, Vice President, Americas Sales, Dassault Systèmes, SolidWorks.

Shounco Design Studios customers will benefit from an increased portfolio that spans product design, simulation, enterprise data management, technical communications, 3d printing systems, engineering services, support and training. With an addition of MCAD’s certified technical experts, this acquisition will make the combined organizations an even stronger business partner.

“Our first priority in considering this merger was our customers. All of our key employees will remain with MCAD and we firmly believe the new company will be stronger and better able to serve the Oregon and Washington SolidWorks user base,” said Paul Shoun, president of Shounco Design Studios, Inc.

Susan Evans, president of MCAD Technologies added, “The merger with Shounco Design Studios, Inc. customer base and high quality technical staff will position MCAD to offer an even higher level of support to SolidWorks Users in the Northwest region. Over the past 12 years Shounco has built an extremely well run organization, which combined with the resources at MCAD will be a benefit to all involved.”

MCAD specializes in sales, support and training of SolidWorks based products; including 3D Solid Modeling, Design Validation and Product Data Management.

For more information, visit: www.mcad.com or www.shounco.com

Bayer MaterialScience and Solid Composites GmbH are partnering to develop thermoplastic polyurethane (TPU) powders for selective laser sintering. This innovative method for fabricating three-dimensional structures is based on the use of a laser beam to sinter powdered starting materials. The start-up company based in Voerde, on the Lower Rhine, will be awarded a brand license to market the new high-tech materials under the name Desmosint. This opens the door to numerous potential applications, for instance in the automotive industry, in sports goods, robotics or aerospace engineering. Solid Composites is a spin-off of the Fraunhofer Institute for Environmental, Safety and Energy Technology (UMSICHT).

“Solid Composites has made a name for itself as a creative developer and supplier of thermoplastic powders for laser sintering and electrostatic coating, among other things, and is therefore the partner of choice for us when it comes to successfully marketing our TPU innovation,” explains Jürgen Hättig, TPU marketing specialist at Bayer MaterialScience.

No molds necessary

Selective laser sintering is becoming a firmly established digital manufacturing method in the additive manufacturing of plastic parts. A part is made from a thermoplastic powder based on the part’s structural design data. Guided by CAD software, a laser fuses successive layers of a powder bed at selected points where the part is to emerge. In other words, the part “grows” layer by layer. “The method eliminates the use of molds, and that cuts costs considerably. Furthermore, in contrast to injection molding, even parts having complex geometries with cavities and undercuts can be rendered,” explains Marcus Rechberger, general manager of Solid Composites.

Material gap closed

Until now, primarily soft, elastic materials and rigid thermoplastics, such as polyamide, were commercially available for selective laser sintering. “Our TPU products, with their high toughness, elasticity and strength, have now closed the gap between these material classes. And that opens the door to good application opportunities,” Hättig says. The first representative of the new class of TPUs is Desmosint X 92 A-1. One of its advantages is that the space in which the TPU is processed layer by layer must be maintained at a temperature of only 80 °C, in contrast to polyamide, for instance, which is processed at slightly below its melting temperature. “Because heating the processing space generates most of the total energy cost, this method results in significant savings on energy. And our TPU has only a very low tendency to warp, meaning the sintering process runs very stably. Lastly, the non-sintered powder does not age inside the processing space and therefore can be used for the next job, an enormous cost advantage compared to the classical laser sintering material PA12,” Hättig explains.

Potential use even in high-volume production

Selective laser sintering typically offers great design freedom and is particularly suited to the additive manufacturing of short to extremely short runs, for instance in the production of components like housing parts, bellows and hoses for full-size and luxury sedans. When used with the TPU products, the method also is ideal for producing custom components, such as orthopedic shoe inlays, athletic shoes, helmets and prosthetic devices. “Beyond that, the technology may prove suitable in high-volume production, too, particularly in those cases where part geometries are very intricate and the cost of injection molds high. In these scenarios, the use of several sintering machines can be more cost efficient,” Rechberger explains. At the end of the part’s service life, the plastic is fully recyclable.

For more information, visit: www.materialscience.bayer.com or www.solidcomposites.de

In industrial environments automated 3D scanning inspection cells have become an important part of various manufacturing processes. The GOM ATOS ScanBox is constructed and engineered to industrial standards to assure highest safety and mobility. Delivery time is short and setup is plug-and-play. The ATOS ScanBox includes an ATOS Triple Scan digitizer, robot, rotary stage, software, safety house, and more. All the elements in one box to ensure automation success. The ATOS ScanBox made its public debut at Control in May. Since then there have been many installations including OEMs and suppliers such as Daimler, Volkswagen, Rolls Royce, Bosch, Eisenwerk Brühl, Dräxlmaier, Delcam and many more. The true definition of “out of box” solution within a box.

The ATOS ScanBox is a plug-and-play measuring cell for fully automated 3D digitizing and inspection. The ATOS ScanBox combines optimized industrial components, mobility and highest safety in an off-the-shelf 3D measuring machine.

ATOS is the most innovative optical measuring system for three-dimensional coordinate measurement on the market. ATOS measures different object sizes, surface finishes, and complexities giving versatility to 3D digitizing by delivering:

  • Accurate 3D coordinates and high data quality
  • Full-field deviation to CAD, 2D and part-to-part
  • Section-based analysis, GD&T and trend analysis
  • Complete measuring reports

For more information, visit: http://www.gom.com/metrology-systems/system-overview/atos-scanbox.html

A team of engineering students at Polytechnic Institute of New York University (NYU-Poly) won the Judges Innovation Design Award in a NASA contest that challenges college teams to build an efficient digging machine for the moon.

The soil of the moon has minerals that potentially can be mined, but in order to do so, NASA needs a light and efficient digging machine. To construct one, as well as encourage students in science, technology, engineering and mathematics – the STEM subjects – NASA sponsors a contest in which college students build a lunar excavation device called a Lunabot.  Fifty-eight teams competed in NASA’s Third Annual Lunabotics Mining Competition at the Kennedy Space Center in Florida.

Its project also received NYU-Poly’s first Paul Soros Prize for Creative Engineering, named for the alumnus whose engineering changed ports throughout the world.

The main test for the Lunabots was to mine and drop in a bin 10 kilograms (about 22 pounds) of simulated lunar dirt within 10 minutes. Challenges included the abrasive nature of lunar soil, the bot’s weight and team-to-robot communications.

“On the moon, dust eats away at everything,” said team captain Stanislav Rosylakov, who graduated in May in civil engineering and is enrolled at NYU-Poly for graduate school. Poly’s Lunabot had very good dust tolerance, he explained, as all the belts and chains were inside the structural frame. “Our robot was light, which is important because it costs so much to send supplies to the moon,” he said. For communications, NYU-Poly’s was one of the few teams that didn’t use a laptop, instead installing a small microcontroller with a Wi-Fi attachment.  

In addition, most of the teams built bulldozers, the simplest way to dig, while Team Atlas used a track, with scoops as part of the treads. “It could do somersaults, flip forward and get back on its feet,” noted Jessica Aleksandrowicz, from East Rutherford, New Jersey, an electrical engineering major who just finished her junior year.

The team used bright NYU-Poly green for parts, thanks to its 3D printer, a MakerBot Thing-O-Matic. The NYU-Poly students’ bot was festooned with a flag, Statue of Liberty and the Empire State Building. They also made parts for other teams and little rockets for kids who came by their lunapit.

Along with Rosylakov and Aleksandrowicz, Team Atlas included Yusif Nurizade, (Electrical Engineering, BS 2013), who developed the software for wireless communication; Jack Poon (Mechanical Engineering, BS 2012), who engineered the excavation hardware and systems;  Nick Cavaliere (Mechanical Engineering, BS 2012), who engineered the power transmission, manufacturing and overall optimization;  Salvatore DiAngelus (Computer Engineering, BS 2013), who integrated hardware and software for wireless communication and control and worked on the onboard communications; Matthew Izberskiy (Computer Engineering, BS 2015), who engineered the data transfer and graphical user interface for wireless communication and control; and Ryan Caeti (Mechanical Engineering, MS 2012), who integrated hardware and software, engineered network communication and developed the graphical user interface.  In addition to his role of team captain, Rosylakov optimized the craft for the lunar soil conditions.  Aleksandrowicz was in charge of the website, media and fundraising.

The NASA competition also included a social media component, a 20-page paper and outreach. To educate about and promote STEM and space exploration, the NYU-Poly students visited the Urban Assembly Institute of Math and Science for Young Women and The Christa McAuliffe School (I.S. 187), both in Brooklyn.

Atlast succeeded, said the team’s faculty advisor, Alexey Sidelev of the NYU-Poly Department of Civil Engineering, because students “were passionate about what they were doing and devoted a great deal of time to the project. They really worked as a team. They are proud to be engineers.” He added that the judges “said they liked everything about the NYU-Poly robot. The judges were cheering for them! I never saw judges so involved with a team.”

The best part of the competition, team captain Rosylakov added, is that the NYU-Poly students “got to see SpaceX launch! We met astronauts, and they complimented us. A few of us possibly have job offers from NASA.”

The Paul Soros Prize for Creative Engineering is a $10,000 annual prize established through a gift from Paul Soros, who earned his master’s of engineering degree in 1950 from what was then Polytechnic Institute of Brooklyn and served as a trustee from 1977 until 2007. NYU-Poly established the prize this year in recognition of Soros’s creative engineering solutions that improved port operations and his entrepreneurial acumen. The prize will be awarded each year to an individual student or a team from the fields of civil or mechanical engineering for the most innovative design idea or invention.  

Judging the first Paul Soros award were a panel of distinguished engineering faculty and alumni including Konstantinos "Gus"Maimis (’84 CE), vice president and project executive of WTC Memorial & Museum Projects;Jay Shapiro (’77 ME), vice president of Howard I. Shapiro & Associates Consulting Engineers, P.C.; Masoud Ghandehari, NYU-Poly associate professor of civil engineering; and Joseph Borowiec, NYU-Poly industry associate professor of mechanical engineering.

The team received support from Verizon Foundation, Space Exploration Technologies Corporation (SpaceX), BatterySpace and MakerBot.

For more information, visit: www.poly.edu

Husky Injection Molding Systems today announced additional investments to support its continued growth in China with plans to establish a new manufacturing facility in the region of Suzhou. Ongoing investments will enable Husky to improve local support, reduce lead times and more responsively react to the needs of its rapidly growing customer base in the region.

“Husky has enjoyed long-standing relationships with many customers throughout China. Strong increase in demand for plastics in the region has helped fuel customer growth and we have been fortunate enough to grow with our customers. Today, Asia Pacific represents one of the largest and most dynamic markets the company serves,” said John Galt, Husky’s President and CEO. “Our investment in Suzhou is a step toward ensuring we are able to meet the growing expectations of customers in this region. Our goal is to be increasingly nimble and agile to provide the best, most responsive service and support – not only to China, but to markets globally.”

Purchase of land in Suzhou

Husky recently signed an investment agreement with the local government in Suzhou to purchase 53,000 square meters (80 mu) of land in this region. The area of land is located in the Suzhou New District and is a Greenfield site that has significant opportunity for further expansion beyond the existing land area. Husky plans to establish a state-of-the-art manufacturing location that will further increase local capacity to improve customer support and shorten lead times. The site is expected to be fully operational in 2014 and will add to the company’s already strong presence in China.

Investments to improve local support

Working with the industry’s largest service and sales network, Husky is continuously investing in its global infrastructure to meet customers’ specific needs. Over the last several years, Husky has strengthened its presence and supply chain capabilities in China. Since first establishing a presence in 2004, Husky has more than doubled its footprint in the region and has more than tripled its regional workforce. The Suzhou facility will complement Husky’s existing facilities, most notably the Shanghai Technical Center. Opened as Husky’s Asia Pacific headquarters, the Shanghai location has also doubled its footprint since 2004, expanding in 2006 and again in 2009. It continues to be a central hub for the region and is responsible for a number of key activities, including service and sales, development engineering, human resources, finance, machine assembly and hot runner manufacturing.

To accommodate growing hot runner business in the region, Husky has also made recent investments in hot runner refurbishing, hot runner manufacturing and mold conversion capacity. A key focus of these initiatives is to continue to reduce lead times and improve responsiveness, supporting the company’s overall strategy to serve customers in the region more effectively.

Husky Injection Molding Systems is a leading global supplier of injection molding equipment and services to the plastics industry. The company has more than 40 service and sales offices, supporting customers in over 100 countries. Husky's manufacturing facilities are located in Canada, the United States, Luxembourg, Austria and China.

For more information, visit: www.husky.ca

Goodrich Foundation has awarded Workshop for Warriors (WfW) in San Diego, Calif. $100,000 to support its program that provides job training and skill certification to U.S. veterans at no cost to students. WfW provides training in welding, milling and machining for wounded, homeless veterans and service men and women about to transition out of active duty into civilian life. Thousands of veterans are expected to end their military careers over the next several months as the conflicts in Iraq and Afghanistan wind down.

"One area of our giving focus at Goodrich is to honor the men and women who serve their country in the armed forces," said Marc Duvall, president of Goodrich's Aerostructures business. "Enabling Workshops for Warriors to provide much-needed job training to veterans one of the best ways that we as a company can tell our veterans, 'Thank you for your service.'"

Many returning veterans will come through San Diego on their way back to their hometowns, making Workshops for Warriors ideally located to assist them with their career transitions. In addition to helping veterans establish careers in an extremely tight job market, the program also benefits the country.

"America is hungry for manufacturing employees; there are more than two million unfilled manufacturing jobs in the U.S. right now," Hernan Luis y Prado, president Workshops for Warriors said. "Hiring our graduates is a win-win for this country and the people who served it. We want to be a major driver for retraining the world's greatest fighting force into the world's most modern manufacturing force."

Last month, Luis y Prado was recognized as a "Champion of Change" for establishing Workshops for Warriors and his dedication to helping members of the armed forces.

The Goodrich Foundation grant will be used to hire additional instructors in order to increase the number of graduates from Workshops for Warriors. The organization currently has a 100 percent job placement rate for its students.

This is the second Goodrich Foundation grant for the organization. In late 2011, WfW received a $25,000 grant to help it establish its curriculum. In addition, Goodrich Aerostructures business in Chula Vista, Calif., has donated nearly $1 million in equipment and materials to help WfW build out its class offerings.

Goodrich Foundation is the charitable arm of Goodrich Corporation (NYSE: GR). The Foundation provides support to selected charitable institutions in Goodrich's United States headquarters and plant communities.

Goodrich Corporation, a Fortune 500 company, is a global supplier of systems and services to the aerospace and defense industry.  With one of the most strategically diversified portfolios of products in the industry, Goodrich serves a global customer base with significant worldwide manufacturing and service facilities.

For more information visit: www.workshopsforwarriors.org or www.goodrich.com

The Industrial Designers Society of America (IDSA) unveiled the winners of the 2012 International Design Excellence Awards (IDEA®) program—a celebration of design excellence in products, sustainability, interaction design, packaging, strategy, research and concepts. Out of 660 finalists, 35 were honored with the Gold Award, while 71 received the Silver Award and 123 merited the Bronze Award. IDSA will reveal the Best in Show, Curator’s Choice, People’s Choice and the Sustainability Award at the IDEA ceremony on Aug. 18 at its 2012 International Conference in Boston.

The top corporate winners were Samsung claiming seven awards, Belkin securing four and Coway and LG Electronics receiving three each.

Among design firms: IDEO received 13 awards; Smart Design captured six awards; Teague, fuseproject, Nectar Inc. and NewDealDesign LLC earned four each; and frog, New, Ziba and Ammunition won three respectively. Art Center College of Design, in Pasadena, Calif., topped this year’s list of college wins with eight awards.

“I believe the diversity of experts and opinions within this year’s jury shaped the debate and ultimately made a statement—not only about the best design of 2012, but also setting a clear direction for the future,” said IDEA’s 2012 Jury Chair Rhys Newman, head of advanced projects at Nokia. “This year's jury awarded products that brought together hardware, software, service and experience. While there are many well-designed, innovative products, the exciting future is in the convergence of disciplines and expertise that span the digital and physical divide, ultimately resulting in useful and beautiful products for people.”

“In deliberating on the Best in Show, the important bellwether for where the cutting-edge concerns of the profession are, we witnessed the jurors turn from products that demonstrated great experiences to those that combined all the elements of new digital experiences into solutions that can transform behavior,” said IDSA’s Chair George McCain.”

Comprising the IDEA 2012 jury, 19 international design experts from design consultancies, corporations and universities spent weeks previewing entries online and two-and-a-half days of face-to-face debate and hands-on evaluation of the entries at The Henry Ford in Dearborn, Mich. Judging criteria focused on eight areas of industrial design excellence: innovation; benefit to the user; benefit to society; benefit to the client; visual appeal and appropriate aesthetics; usability, emotional factors and unmet needs for the design research category; and internal factors, methods, strategic value and implementation for the design strategy category.

The awards were chosen from the following industry and design categories:  bathroom, spa and wellness; commercial and industrial products; communication tools; computer equipment; design strategy; digital design; entertainment; environments; gardens and outdoor; kitchens; leisure and recreation; living room and bedroom; medical and scientific products; office and productivity; packaging and graphics; personal accessories; research; service design; social impact design; student designs and transportation. Entries came from 30 countries, including Australia, Austria, Canada, China, Colombia, Denmark, Finland, France, Germany, Hong Kong, Hungary, India, Iran, Israel, Italy, Japan, Jordan, Korea (North), Korea (South), Liechtenstein, Mexico, Netherlands, Poland, Singapore, Spain, Sweden, Taiwan, Turkey, United Kingdom and the United States.

The partners and media sponsors for this year’s awards are Core 77, Curve magazine, facesofdesign.com, Microsoft and Yanko Design. This is the third year that The Henry Ford will house the IDEA winners in its permanent collection as it continues to tell the story of innovation.

For detailed descriptions, photos and contact information on this year’s IDEA winners, visit: www.idsa.org/idea-2012-gallery

Researchers are hopeful that new advances in tissue engineering and regenerative medicine could one day make a replacement liver from a patient’s own cells, or animal muscle tissue that could be cut into steaks without ever being inside a cow. Bioengineers can already make 2D structures out of many kinds of tissue, but one of the major roadblocks to making the jump to 3D is keeping the cells within large structures from suffocating; organs have complicated 3D blood vessel networks that are still impossible to recreate in the laboratory.

Now, University of Pennsylvania researchers have developed an innovative solution to this perfusion problem: they’ve shown that 3D printed templates of filament networks can be used to rapidly create vasculature and improve the function of engineered living tissues.

The research was conducted by a team led by postdoctoral fellow Jordan S. Miller and Christopher S. Chen, the Skirkanich Professor of Innovation in the Department of Bioengineering at Penn, along with Sangeeta N. Bhatia, Wilson Professor at the Massachusetts Institute of Technology, and postdoctoral fellow Kelly R. Stevens in Bhatia’s laboratory.

Without a vascular system — a highway for delivering nutrients and removing waste products — living cells on the inside of a 3D tissue structure quickly die. Thin tissues grown from a few layers of cells don’t have this problem, as all of the cells have direct access to nutrients and oxygen. Bioengineers have therefore explored 3D printing as a way to prototype tissues containing large volumes of living cells.

The most commonly explored techniques are layer-by-layer fabrication, or bioprinting, where single layers or droplets of cells and gel are created and then assembled together one drop at a time, somewhat like building a stack of LEGOs.

Such “additive manufacturing” methods can make complex shapes out of a variety of materials, but vasculature remains a major challenge when printing with cells. Hollow channels made in this way have structural seams running between the layers, and the pressure of fluid pumping through them can push the seams apart. More important, many potentially useful cell types, like liver cells, cannot readily survive the rigors of direct 3D bioprinting.

To get around this problem, Penn researchers turned the printing process inside out.

Rather than trying to print a large volume of tissue and leave hollow channels for vasculature in a layer-by-layer approach, Chen and colleagues focused on the vasculature first and designed free-standing 3D filament networks in the shape of a vascular system that sat inside a mold. As in lost-wax casting, a technique that has been used to make sculptures for thousands of years, the team’s approach allowed for the mold and vascular template to be removed once the cells were added and formed a solid tissue enveloping the filaments.

“Sometimes the simplest solutions come from going back to basics,” Miller said. “I got the first hint at this solution when I visited a Body Worlds exhibit, where you can see plastic casts of free-standing, whole organ vasculature.”

This rapid casting technique hinged on the researchers developing a material that is rigid enough to exist as a 3D network of cylindrical filaments but which can also easily dissolve in water without toxic effects on cells. They also needed to make the material compatible with a 3D printer so they could make reproducible vascular networks orders of magnitude faster, and at larger scale and higher complexity, than possible in a layer-by-layer bioprinting approach.

After much testing, the team found the perfect mix of material properties in a humble material: sugar. Sugars are mechanically strong and make up the majority of organic biomass on the planet in the form of cellulose, but their building blocks are also typically added and dissolved into nutrient media that help cells grow.

“We tested many different sugar formulations until we were able to optimize all of these characteristics together,” Miller said. “Since there’s no single type of gel that’s going to be optimal for every kind of engineered tissue, we also wanted to develop a sugar formula that would be broadly compatible with any cell type or water-based gel.”

The formula they settled on — a combination of sucrose and glucose along with dextran for structural reinforcement — is printed with a RepRap, an open-source 3D printer with a custom-designed extruder and controlling software. An important step in stabilizing the sugar after printing, templates are coated in a thin layer of a degradable polymer derived from corn. This coating allows the sugar template to be dissolved and to flow out of the gel through the channels they create without inhibiting the solidification of the gel or damaging the growing cells nearby. Once the sugar is removed, the researchers start flowing fluid through the vascular architecture and cells begin to receive nutrients and oxygen similar to the exchange that naturally happens in the body.

The whole process is quick and inexpensive, allowing the researchers to switch with ease between computer simulations and physical models of multiple vascular configurations.

“This new platform technology, from the cell’s perspective, makes tissue formation a gentle and quick journey,” Chen said, “because cells are only exposed to a few minutes of manual pipetting and a single step of being poured into the molds before getting nourished by our vascular network.”

The researchers showed that human blood vessel cells injected throughout the vascular networks spontaneously generated new capillary sprouts to increase the network’s reach, much in the way blood vessels in the body naturally grow. The team then created gels containing primary liver cells to test whether their technique could improve their function.

When the researchers pumped nutrient-rich media through the gel’s template-fashioned vascular system, the entrapped liver cells boosted their production of albumin and urea, natural components of blood and urine, respectively, which are important measures of liver-cell function and health. There was also clear evidence of increased cell survival around the perfused vascular channels.

And theoretical modeling of nutrient transport in these perfused gels showed a striking resemblance to observed cell-survival patterns, opening up the possibility of using live-cell data to refine computer models to better design vascular architectures.

Though these engineered tissues were not equivalent to a fully functioning liver, the researchers used cell densities that approached clinical relevance, suggesting that their printed vascular system could eventually be used to further research in lab-grown organs and organoids.

“The therapeutic window for human-liver therapy is estimated at one to 10 billion functional liver cells,” Bhatia said. “With this work, we’ve brought engineered liver tissues orders of magnitude closer to that goal, but at tens of millions of liver cells per gel we’ve still got a ways to go.

“More work will be needed to learn how to directly connect these types of vascular networks to natural blood vessels while at the same time investigating fundamental interactions between the liver cells and the patterned vasculature. It’s an exciting future ahead.”

With promising indications that their vascular networks will be compatible with all types of cells and gels, the team believes their 3D printing method will be a scalable solution for a wide variety of cell- and tissue-based applications because all organ vasculature follows similar architectural patterns.

“Cell biologists like the idea of 3D printing to make vascularized tissues in principle, but they would need to have an expert in house and highly specialized equipment to even attempt it,” Miller said. “That’s no longer the case; we’ve made these sugar-based vascular templates stable enough to ship to labs around the world.”

Beyond integrating well with the world of tissue engineering, the researchers’ work epitomizes the philosophy that drives much of the open source 3D printing community.

“We launched this project from innovations rooted in RepRap and MakerBot technology and their supporting worldwide communities,” Miller said. “A RepRap 3D printer is a tiny fraction of the cost of commercial 3D printers, and, more important, its open-source nature means you can freely modify it. Many of our additions to the project are already in the wild.”

Several of the custom parts of the RepRap printer the researchers used to make the vascular templates were printed in plastic on another RepRap. Miller will teach a class on building and using these types of printers at a workshop this summer and will continue tinkering with his own designs.

“We want to redesign the printer from scratch and focus it entirely on cell biology, tissue engineering and regenerative medicine applications,” Miller said.

In addition to Miller, Chen, Bhatia and Stevens, the research was conducted by Michael T. Yang, Brendon M. Baker, Duc-Huy T. Nguyen, Daniel M. Cohen, Esteban Toro, Peter A. Galie, Xiang Yu and Ritika Chaturvedi of Penn Bioengineering, along with Alice A. Chen of MIT. Bhatia is also a Howard Hughes Medical Institute investigator.

This research was supported by the National Institutes of Health, the Penn Center for Engineering Cells and Regeneration and the American Heart Association-Jon Holden DeHaan Foundation.

For more information, visit: www.upenn.edu

Alcoa (NYSE:AA) today announced the first commercial success of its ColorKast™ technology in the consumer electronics market. As a result of this innovative technology, Alcoa can produce color anodizable aluminum die cast components with high-end cosmetics. The first use of the ColorKast™ technology appears on Samsung’s new digital camera NX210 and other consumer electronic OEMs are preparing to apply this technology to their products.

ColorKast™ is a breakthrough aluminum die casting technology that allows consumer electronics manufacturers to create cosmetically high-end, lightweight, and cost-effective components for portable electronic devices using proprietary alloy, process, and finishing technologies developed at Alcoa Technical Center. The result is cosmetic 3D products with the rich, metallic “look and feel” of anodized aluminum, and the high productivity and cost advantages of die castings as compared to unibody machining processing or magnesium die casting. In addition, products made from ColorKast™ create a better green solution relative to plastics or composites because aluminum is infinitely recyclable.

The performance and aesthetic requirements of ColorKast™ have been validated with Alcoa’s exclusive manufacturing partner, GK (Global Kwangsung) in South Korea, before being introduced to the market, leading to the success of the first commercialized application at Samsung.

For more information, visit: www.alcoa.com/con_electronics

Fabricating Partners, Inc. today launched Fabricating.com, the industry’s new online Request for Quote (RFQ) Marketplace designed to help U.S. Buyers build U.S. Supplier networks and manufacture made-to-order parts. Their SourceNow platform presents easy-to-use functionality designed to streamline and manage the complexities of sourcing custom-manufactured products, parts, and assemblies.  From multi-line RFQs to crucial Supplier profiles, Fabricating.com delivers a productive, paperless system developed to address a critical market need for U.S. Buyers seeking U.S. Suppliers. The web-based service supports more than 250 manufacturing processes including machining, sheet metal fabricating, and thermoforming. Fabricating.com requires no IT setup, software installations, or maintenance. Buyers only need Internet access and a standard browser to “source” from any location.
 
Fabricating.com also launched their “Sparks Fly” marketing campaign to introduce the service and encourage reshoring of manufacturing jobs. The rising price of fossil fuel, climbing overseas labor costs, the declining dollar, and compelling “total cost to own” factors are compelling American enterprises to reconsider their manufacturing strategies and logistics. These current market trends were key drivers for Fabricating.com, which is well positioned to help companies create new supplier networks, reshore manufacturing jobs, support Buy American provision requirements, aid State MEPs with “Made in YourState” initiatives, and verify the “country-of-origin” labeling concept for products sold in America.
 
“We are confident Fabricating.com will set the new standard for Sourcing in the United States,” states Frank Russo, Fabricating.com CEO. “In order to revitalize the nation's manufacturing base, we have to encourage the cooperation and coordination of U.S. Buyers and U.S. Suppliers engaged in the Request for Quote process. Our ultra-intelligent SourceNow platform facilitates this interaction and delivers huge benefits to both U.S. Buyers and U.S. Suppliers. Fabricating.com delivers the tools needed by Engineers and Purchasing professionals to carve out next-gen Supplier networks that stimulate the economy and energize our nation of makers.”

Helping Buyers Build U.S. Supplier Networks
 
Fabricating.com’s SourceNow platform is engineered for maximum throughput of RFQ (Request for Quote) requirements. The system analyzes part details from a Buyer’s RFQ and locates U.S.-based contract manufacturers with the expertise and machine assets needed for the job. Suppliers use the same streamlined, paperless system to quote for business. The sourcing platform adheres to the newest Web standards and provides support for CAD files, Excel spreadsheets, and other popular engineering file formats. The solution can also be integrated with Buyside enterprise applications, and provides a central point for all sourcing intelligence with a host of management tools and analytics for any size purchasing department.
 
Helping U.S. Suppliers Fill their Business Pipeline
 
The Fabricating.com marketplace provides RFQ opportunities for U.S. Suppliers who want to build a customer pipeline or expand their current client base. The sourcing system analyzes each RFQ posted online by Buyers, then flags the Supplier when an opportunity precisely matches their expertise, capacity, and machine assets. Based on detailed engineering drawings and documentation provided, Suppliers use the same paperless system to quote for the job. A strategic business development tool, Fabricating.com can also be utilized to manage quotes, standardize procedures, and diminish the headache of missing engineering drawings and documents.  

For more information, visit: www.Fabricating.com

PCS Engineering, Inc., a product development services company and Objet Geometries reseller will host 3D printing, 3D scanning and CNC software seminars in select Maryland, Pennsylvania and Virginia venues this summer.

"The road show will display how leading manufacturers use CAD/CAM software, 3D scanning and 3D printing technologies to accelerate the product development process," said PCS Engineering, Inc. CEO Michael Huggins. "It is intended for manufacturing professionals seeking to improve operations with greater efficiencies in terms of cost and time required to bring new products to market."

Technology providers will include software and equipment demonstrations such as:

  • DP Technology: Computer-Aided Manufacturing (CAM) Software
  • Epilog Lasers: CO2 Laser Engraving Systems - Special Feature Laser Cutting Demonstration
  • GoMeasure3D: 3D Scanning, Inspection and Reverse Engineering 3D Measurement Reverse Engineering and Inspection Solutions - Special Feature the Microscribe Portable CMM Measurement Arm Demonstration
  • Objet: 3D PolyJet™ Matrix technology and Digital Materials - Special Feature Objet30 Demonstration
  • Siemens PLM: SolidEdge Software Modeling and Assembly Tools

2012 PCS Engineering, Inc. Road Show Schedule:

  • June 25: Marriott SpringHill Suites Virginia Beach Oceanfront, 901 Atlantic Ave., Virginia Beach, VA
  • June 26: NASA Langley Research Center*, Hampton, VA
  • June 27: Newport News Marriott at City Center, 740 Town Center Dr., Newport News, VA
  • June 28: Richmond Marriott, 500 East Broad St., Richmond, VA
  • July 9: Philadelphia Marriott West, 111 Crawford Ave., West Conshohocken, PA
  • July 10: Courtyard Reading Wyomissing Hotel Marriott, 150 North Park Road, Reading, PA
  • July 11: Lancaster Marriott at Penn Square, 25 South Queen St., Lancaster, PA
  • July 12: Courtyard Harrisburg Hershey Marriott, 725 Eisenhower Blvd., Harrisburg, PA
  • July 30: Virginia Tech, Blacksburg, VA
  • July 31: Virginia Western Community College, 3094 Colonial Ave., Fishburn Hall F206, Roanoke, VA
  • August 1: James Madison University, Festival Conference Center, 1301 Carrier Dr., Harrisonburg, VA
  • August 2: Harley Davidson of Fredrick, RR 255 Frederick, MD

Road Show events run 10:00am to 3:00pm and will include live 3D printing, 3D imaging and laser cutting and software demonstrations from technology experts.

Industrial designers and manufacturing engineers interested in 3D printing a part should send a CAD model in .STL format to This e-mail address is being protected from spambots. You need JavaScript enabled to view it one week prior to each scheduled event. Space is limited and available on a first-come, first-service basis. During 3D imaging demonstration, PCS Engineering, Inc. will scan mechanical shapes and provide the data output to attendees.

PCS Engineering, Inc. offers design engineering, rapid prototyping and additive manufacturing solutions to industrial designers and manufacturing engineers. PCS Engineering, Inc. delivers prototypes and parts in a comprehensive range of plastic and metal production grade materials. Services include 3D Data Capture, Scanning and Revere Engineering, Stereolithography, Selective Laser Sintering, Selective Laser Melting, 3D Printing, CNC Machining, RTV Molding, Urethane Casting, Die Casting. PCS is an Objet Geometries reseller and offers access to Objet Connex500™, Connex350™, Objet260 Connex™, Eden500V™, Eden 350/350V™, Eden 260V™, Eden250™, Objet24 Personal 3D Printer and the Objet30 Desktop 3D Printer to the region.

For more information, visit: www.pcsenginc.com/index.php/viewevents/events

CIMdata, Inc., the leading global Product Lifecycle Management (PLM) management consulting and research firm announces that Dr. David E. Cole, Chairman Emeritus, Center for Automotive Research (CAR), will make a keynote presentation at PLM Road Map™ 2012, which will take place at The Inn at St. John’s, outside of Detroit, on October 2 and 3.

The auto industry has experienced a period of turmoil and challenge—indeed, a perfect storm—during the past decade. Every aspect of the industry was impacted by the “great recession,” which turned out to be a depression for the auto industry. Fortunately, the industry is coming back strong. The auto industry and manufacturing in general are critical to a successful economy, with a high job multiplier and significant value creation.

In his keynote presentation, “The Auto Sun is Rising,” Dr. Cole will address the dramatic changes that are occurring in the industry from the new evolving business model to the exploding importance of knowledge and innovation. The industry of the future and the exciting potential for new powertrains, fuels, connected vehicles, material systems, and engineering and manufacturing methods that will reshape the industry and its products will be discussed. The presentation will also address possible “choke points” that could interrupt progress, such as the lack of talent, critical materials, appropriate policy, and supply disruptions.

PLM Road Map™ 2012 is the must-attend event for industry executives and PLM practitioners globally—providing independent education and a collaborative networking environment where ideas, trends, experiences, and relationships critical to the industry germinate and take root. It is a strategic conference focused on how companies are successfully employing PLM strategies and enabling solutions to meet challenging product development, manufacturing, and deployment issues. PLM Road Map™ 2012 is a two-day event that will challenge attendees to shift their current thinking to a new level in a series of presentations focusing on the global transformation of product development and innovation processes.

About Dr. David E. Cole, Chairman Emeritus, Center for Automotive Research

Dr. David E. Cole is the Chairman Emeritus of the Center for Automotive Research (CAR) in Ann Arbor, Michigan. He was formerly Director of the Office for the Study of Automotive Transportation (OSAT) at the University of Michigan Transportation Research Institute and an engineering professor at the University of Michigan.

Dr. Cole’s recent research has focused on strategic issues related to the restructuring of North American industry and trends in globalization, technology, market factors, and human resource requirements. He is chairman of Auto Harvest, a new organization being developed to facilitate the flow of intellectual property in and out of the auto industry.

He is active in SAE, including serving two terms on the Board of Directors. In February 1986, Dr. Cole was named a Fellow of SAE. He is also active in the Engineering Society of Detroit and was elected to Fellow status in 1990. In 2000, he received the Engineering Society’s highest award, the Horace H. Rackham medal. Dr. Cole is also a member of the Society of Manufacturing Engineers and was elected to Fellow grade in 2009.

Dr. Cole received his B.S.M.E. and Mathematics, M.S.M.E., and Ph.D. from the University of Michigan and recently received an honorary doctorate from Cleary University.

For more information, visit: plmforesight.cimdata.com/index.cfm?content=include_conference12.cfm

Friday, 15 June 2012 11:34

Register Today! Tecplot Chorus Webinar

Written by

Recently, Tecplot announced Tecplot Chorus 2012, our most advanced CFD visualization management system to date. And in order to help our users take advantage of new features and enhancements, we’re holding a free webinar on Thursday, June 21 at 10 a.m. PST.

Join Dr. Durrell Rittenberg as he illustrates Chorus’ new features by evaluating blade optimization and performance prediction studies of an unmanned aerial vehicle (UAV). In each study, he will show you how to:

  • Evaluate results from multiple simulation cases
  • Model system performance with surrogate models
  • Compare results qualitatively and quantitatively
  • Use results to create reports

Thursday, June 21, 2012
10:00 AM - 11:00 AM PDT

After registering you will receive a confirmation email containing information about joining the webinar.

If you have any questions about Tecplot Chorus or the webinar, please contact us at 425-653-1200

For more information or to register, visit: https://www1.gotomeeting.com/register/223804721

EON Reality, the world's leading interactive 3D software provider, today released EON Creator 4.8, an easy-to-use eLearning authoring tool that integrates 3D concepts with the web, PowerPoint, videos, sounds, animations and more into complete, blended learning environments. The new release also comes with an updated website look and new video tutorials.

With EON Creator 4.8, users can create unique educational 3D lessons and interactive scenes using high-quality 3D components from the EON Experience portal and blend them together with their own 3D content. The portal contains thousands of models and scenes accessible directly from inside the EON Creator authoring tool. Once content is downloaded into EON Creator, users can add contextual knowledge to any 3D object in their scene. Users can also link multiple 3D scenes together to create continuous learning environments.

3D content can then be published automatically in the EON Experience portal or shared in a live 3D multi-user session in EON Coliseum. EON Creator can present the virtual 3D learning experience across multiple devices- from laptops to 3D projected displays.

“With our rapidly growing community of EON Creator users we are pleased to be able to release this major upgrade with many enhanced functionalities and requested features. Our goal is to provide the easiest and most intuitive workflow for interactive 3D content development for education, allowing teachers and instructors as well as our fastest growing user segment students to start producing content quicker,” said Mats W. Johansson, President, EON Reality, Inc.

The new EON Creator 4.8 release brings a range of updates and improvements to the EON Experience platform, where the most notable additions are:

  • Improved creation process in Quiz mode: Users can now create customized questions and answers using the Quiz function, as well as separate the Quiz and Annotation function as desired.
  • Expanded support for more stereo devices: EON Creator Pro can now support three modes of stereoscopic 3D: Top/Bottom, Interleaved, and Frame Sequential 3D.
  • Recording video of your content is now easier than ever: Users can upload their experiences with 3D lessons directly to YouTube.
  • Simplified login process: Users can now signup and login with a single click via Facebook, LinkedIn, Twitter, and Google+.
  • Expanded file support for EON Experience Player: The EON Experience Player can now open EON Experience simulation (.edz, .eop, .eoz) and EON Experience scene files (.eos).
  • Easier user interactions: Users can now explore different parts of an object with a single click.
  • Configuration of pivot-points for 3D objects: The pivot-point is the central point where an object is rotated around.

EON Reality, Inc. is the world's leading interactive 3D solutions provider for businesses and education based on Virtual Reality technology. EON Reality provides state-of-the-art 3D display technology for immersive and stereoscopic viewing, from portable tablet PCs and glass free stereo display systems to curved-screen and immersive rooms consisting of multi-channel projection walls. The technology foundation for developing interactive digital content includes importing the most common 3D animation formats into EON's authoring software and creating modules and applications that can be viewed on various display systems. EON’s technology solutions enable all organizations to more effectively visually communicate, collaborate and accelerate knowledge transfer.

For more information, visit: www.eonexperience.com/eon-creator/eon-creator.aspx

Alcoa's Kawneer business and The American Institute of Architecture Students (AIAS) announce today the Enlightening Libraries: Student Design Competition. Sponsored by Kawneer and administered by the AIAS, this competition will challenge students to redesign a dated public library that is an effectively urbanized, collaborative community space appealing to all generations and integrating the most recent technologies. Total prize money is $7,750, including $3,000 for the first place winning design team.

The competition, now in its seventh year, challenges students to learn about building materials and techniques, specifically architectural aluminum building products and systems, while demonstrating an understanding of sustainable design. Participants are required to integrate a variety of Kawneer products, from entrances and framing systems to windows and curtain wall systems as they relate to efficient community spaces, to develop a new-age library that embraces an atmosphere of enlightenment and learning.

A jury of four architectural professionals will evaluate submissions based on ingenuity and originality as well as design clarity and the ability to create an aesthetic that compliments the community and environment. Appropriate use of materials, including light shelves and sunshades that enhance natural light, will be key factors in the evaluation and selection of winning designs.

Developed to engage architecture and design students from schools worldwide, contest submissions can be the work of an individual or a group of up to four students. Students interested in participating in the competition must register no later than October 14, 2012. Submissions must be made digitally via the competition website on or before November 29, 2012. Winning entries will be published in the Spring 2012 issue of Crit, Journal of the AIAS and will be on display at the 2013 AIA Convention and Design Exposition in Denver, Colorado, June 2013.

For more information or to register, visit: kawneer.aias.org

The North American Die Casting Association (NADCA) will host its Die Casting Congress & Exposition October 8-10, 2012, at the Indiana Conventions Center – Halls A&B in Indianapolis, IN.

This event will feature three days of Congress sessions, technical and management presentations that will be given by experts from around the world. These presentations will expose metalcasters to the latest technology, ongoing research and successful management tools that will assist companies in enhancing their competitiveness.

“We are excited to once again offer a “die casting-only” trade show and look forward to bringing thousands of die casters to this event to see and learn about products, services and advancements in the die casting industry,” said Twarog.

This exposition will also feature more than 100 exhibitors, the International Die Casting Design Competition, the Design Competition Luncheon and the Die Casting Industry Gala. Over 75% of booth space has been sold!

The Die Casting Congress & Exposition is an exclusive event to the die casting industry and its suppliers.  The 2015 Die Casting Congress & Exposition will also be held in Indianapolis due to its centralized location for the convenience of the die casting industry.

For more information or to register, visit: www.diecasting.org/congress

We at FineLine Prototyping are excited to announce the launch of MicroFine Metal, the newest technology of our high-quality, precision rapid prototyping services. We are pleased to be the first in the industry to offer metal prototypes at the highly detailed resolution that we are known for producing, affording us the opportunity to serve you in new and innovative ways.

We discovered through surveying our customers that there was a great need for precision metal parts made quickly. We set about finding a solution that produced precision, full-strength metal parts that our customers could order as quickly and easily as plastic parts. After two years of research and development, we are happy to now have that service in place. We can now meet the needs of our customer base by producing prototypes – and even production-ready parts – in stainless steel and aluminum.

More specifically, the following materials are available as part of our MicroFine Metal service offering:

MicroFine Metal Direct:

  • Stainless Steel 17-4PH
  • Stainless Steel 316L

MicroFine Metal Casting:

  • Aluminum 6061-T6 (A356.2-T6)
  • Aluminum 2024-T7 (B206.2-T7)

MicroFine Metal parts are built in micro-resolution (.001” layers), making extremely fine details possible. The MicroFine Metal Direct process has a working build envelope of 3.5” by 3.5” by 3”. The process is capable of resolving features down to .005”. Tolerances of +/-.002” or better can be expected on features under 1”. Surface finish of the parts as built is approximately 130 microinches RMS.

The current limitations of the Microfine Metal Casting process are a maximum part dimension of 3”, maximum part volume of 1.5 cu. in., and minimum feature size of .010”. Tolerances of +/- .003” can be expected for features less than 1 in. and +/- .005” for features greater than 1 in. Surface finish of the parts as cast is very fine at approximately 32 RMS – similar to die-cast parts.

We offer finishing options to improve on surfaces if needed. In addition to our standard finishes, optional finishing procedures such as anodizing, electropolish, hand polish, and powder coating/painting are available to meet your every need. If tighter tolerances are required, we offer secondary machining operations such as drilling, slotting, milling and reaming. Discuss your needs with our quoting staff and we will help you select the best finishing method for your part.

For your convenience and just like with our other services, you may upload your files via our online quoter and simply select “metal” as your material choice to get started. A typical turnaround time is 2-4 business days for parts built using MicroFine Metal Direct and 5-6 business days for parts built using MicroFine Metal Casting.

We are very excited about this new service and the ability to now offer precision production-level quality metal prototypes with the ease and speed of plastic parts.

For more information, visit: www.finelineprototyping.com/services/materials.php#metal

rapid prototype and manufacturing (rp+m), located in Avon Lake, Ohio, is receiving their first Objet machine.  Next week rp+m, a product development and prototyping company, is expanding their capabilities by purchasing Objet’s largest build machine, the Objet Connex500.  With this 3D printer, rp+m will be able to simulate an overmold or 2 shot process using Objet’s hard and soft touch material as well as run up to 14 materials in a single build.

rp+m is a sister company of Thogus, an engineering company whose expertise is in plastic injection molding.  rp+m became it’s own entity in 2011 due to the growing demand of rapid prototyping.   With a team of mechanical and biomedical engineers, rp+m can also provide product design, quality and regulatory services.

Features:

  • largest build envelope (19.7 in. X 15.7 in. X 7.9 in.)
  • run up to 14 materials in one build
  • soft touch material
  • simulate overmold or 2 shot process
  • near water clear material
  • quick build times (.75 in./ hour / per strip)
  • very high resolution and accuracy

Markets:

  • animation & entertainment
  • architecture
  • automotive
  • consumer electronics
  • consumer goods
  • defense
  • dental
  • educational
  • hearing Aid
  • industrial machinery
  • jewelry
  • medical
  • medical equipment
  • sporting Goods
  • toys

For more information, visit: www.rpplusm.com

Wednesday, 06 June 2012 11:41

Haas to Showcase 16 Machines at IMTS 2012

Written by

IMTS is the premier manufacturing technology show in the Americas. For 2012, the show is expected to bring together more than 82,000 visitors from 116 countries to see more than 1100 exhibitors from around the world.  This year, Haas will have 16 machines on display in 10,000 square feet of booth space, as well as 3 additional machines in vendor booths. Here’s a list of what’s new since last IMTS:

UMC-750 Universal Machining Center

The Haas UMC-750 is a versatile 5-axis 40-taper VMC with 30" x 22" x 20" travels and an integrated dual-axis trunnion table. The show machine is equipped with a 12,000-rpm inline direct-drive spindle, and comes standard with a 40+1 tool side-mount tool changer. The dual-axis trunnion can position parts to nearly any angle for 5-sided (3+2) machining, or provide full simultaneous 5-axis motion for contouring and complex machining. The 630 x 500 mm table features standard T-slots and a precision pilot bore for fixturing versatility, and the trunnion provides +35 and -110 degrees of tilt and 360 degrees of rotation for excellent tool clearance and large part capacity.
    
ST-10Y Compact Y-Axis Turning Center

The Haas ST-10Y is a small-footprint Y-axis turning center that provides 4" of Y-axis travel (±2" from the centerline) for off-center milling, drilling, and tapping, and comes standard with high-torque live tooling and a servo-driven C axis for versatile 4-axis capability. The machine provides a maximum cutting capacity of 9" x 14", with a swing of 16.25" over the cross slide. It is equipped with a 6.5" hydraulic 3-jaw chuck and a 12-station VDI turret. The ST-10Y’s A2-5 spindle nose has a 2.31" spindle bore and a bar capacity of 1.75". The machine’s 15 hp vector dual-drive spindle turns to 6000 rpm, and provides 75 ft-lb of torque.
    
ST-20SSY High-Speed Y-Axis Turning Center

The Haas ST-20SSY is a high-speed Y-axis turning center that provides 4" of Y-axis travel, and includes high-torque live tooling and a servo-driven C axis to perform secondary machining operations. The machine has a maximum cutting capacity of 10" x 21", and is equipped with a 24-station hybrid BOT/VDI turret. The A2-6 spindle turns to 5000 rpm, and features an 8.3" hydraulic chuck and a 2.0" bar capacity. A 30 hp vector drive system yields 140 ft-lb of torque.

ST-40 Large-Capacity Turning Center

The Haas ST-40 is the largest addition to Haas Automation’s line of new generation turning centers. It has a maximum cutting capacity of 25.5" x 44", with maximum swings of 34.5" over the front apron and 25.5" over the cross slide. The spindle bore is 4.62", with a bar capacity of 4". The machine’s 40-hp vector dual-drive spindle turns to 2400 rpm, and provides 1400 ft-lb of torque. The ST-40 features an A2-8 spindle nose and comes equipped with a 15" hydraulic 3-jaw chuck. A 12-station bolt-on style tool turret is standard, with an option for a hybrid BOT/VDI turret.

DS-30Y Dual-Spindle Y-Axis Turning Center

The Haas DS-30Y turning center combines dual-spindle turning with Y axis, C axis, and live tooling. The opposed spindles support fully synchronized turning, and allow on-the-fly part pass-off to reduce cycle times. The machine comes standard with high-torque live tooling and a servo-driven C axis, and provides 4" of Y-axis travel (±2" from the centerline) for off-center milling, drilling, and tapping. The DS-30Y has a maximum cutting capacity of 18" x 23", and is equipped with a 12-station hybrid BOT/VDI turret. The A2-6 main spindle features an 8.3" hydraulic chuck and a 30 hp vector drive system; the A2-5 secondary spindle also has an 8.3" hydraulic chuck, and is powered by a 20 hp vector drive system. Both spindles turn to 4000 rpm, and have a 2.0" bar capacity.

New 40-Taper Spindles

For 2012, Haas Automation increased the speed and performance of the standard spindle on its expansive line of 40-taper VMCs, and introduced several new optional spindles. All Haas VF-1 through VF-12 40-taper VMCs are now equipped with a powerful 8100-rpm inline direct-drive spindle that is driven by a 30-horsepower vector drive system. An optional 10,000-rpm inline direct-drive spindle is available for shops wanting higher spindle speeds. Both spindles yield 90 ft-lb of cutting torque.

For shops needing additional low-speed torque and wanting the flexibility of a gearbox, two optional gear-drive spindles are also available for standard Haas 40-taper VMCs. The optional spindles provide either 8100-rpm or 10,000-rpm, and feature a Haas-built, high-precision two-speed gearbox. Both geared spindles yield 250 ft-lb of torque.

For more information, visit: www.imts.com/visitor/exdir/exhibitor_details.cfm?exhid=00000725

Tuesday, 05 June 2012 10:02

Capture 3D Measurement Innovation 2012

Written by

The growing need to optimize manufacturing methods are driving companies to advance to accurate and fast non-contact optical 3D measurement solutions to conquer today's and tomorrow's challenges. This educational conference focuses on how companies are improving their design, production, manufacturing, and maintenance processes with optical and structured light measurement technology. Capture 3D is thrilled to be celebrating our 5th biannual conference. This special event is geared for engineers, managers, and executives to learn, discover, assimilate, interact, and collaborate. If you have not already signed up, please remember seating is limited, so register today to participate in this exciting event.

The keynote and guest speaker technical presentations will address 3D measurement applications applicable to various industries for optimizing quality control, inspection, reverse engineering, CFD/FEA analysis, automation, rapid manufacturing, root cause analysis, and much more. The 3D Solutions Expo will showcase the latest innovative 3D measurement equipment and software live.

Goal of the event is to:

  • Learn how companies are utilizing innovative 3D measurement technology into current workflows to reduce costs, speed up processes, and improve time to market
  • Discover techniques for ATOS 3D scanning, TRITOP digital photogrammetry, inspection, reverse engineering, and automation
  • Collaborate with industry professionals and gain insight to help improve various applications
  • See upcoming developments and enhancements from Capture 3D and GOM
  • Receive technical advice and support from Capture 3D, GOM, and attendees
  • Provide feedback on desired functionality and other areas of importance to you
  • Network with people who share similar responsibilities and goals
  • Interact in our hands-on 3D Solutions Expo displaying a series of live labs and solutions experts

Capture 3D Measurement Innovation 2012
Hilton Hotel
3050 Bristol Street Costa Mesa, CA 92626
August 21-23, 2012

For more information or to register, visit: www.capture3d.com/3Dconference/2012.html

EDAC Technologies Corporation (NASDAQ: EDAC), a diversified designer, manufacturer and servicer of precision components for aerospace and industrial applications, announced today that it has acquired EBTEC Corporation, a provider of advanced precision manufacturing processes and fabrication solutions to leading aerospace, power generation, industrial, semiconductor and medical customers.  Privately-owned EBTEC, which is headquartered in Agawam, Mass., had sales of $12.6 million in 2011.

The purchase price was approximately $11 million, of which $1.65 million has been paid in EDAC stock, with the balance funded by financing through TD Bank N.A.

EBTEC Corporation, which was founded in 1963, pioneered the development of non-contact, high energy beam (HB) technologies with the Apollo Space Program, proving at the time that EB welding could meet the demands that space travel would place on engineered products.  Today, in addition to electron beam welding, EBTEC's precision high energy beam processes include laser welding, laser cutting, laser drilling, EDM, vacuum heat treating, and abrasive waterjet cutting, while they also offer comprehensive precision fabrication solutions.  EBTEC has an extensive array of equipment, coupled with substantial engineering, metallurgy, quality assurance, program management, and in-house finishing capabilities. EBTEC is a certified supplier to major aerospace and industrial OEMs.

Dominick A. Pagano, President and Chief Executive Officer of EDAC Technologies, commented, "This acquisition represents an important step forward in our growth strategy. EBTEC gives us highly complementary and advanced capabilities that are required for the manufacture of our precision parts, many of which we formerly outsourced to EBTEC.  EBTEC also fabricates finished components, which immediately expands our product line with additional parts for aircraft engines and ground-based turbines, markets we currently serve.  In addition, EBTEC makes components and products used by manufacturers of semiconductors and medical devices, which opens up new markets to EDAC.  This acquisition also efficiently expands our manufacturing footprint as EBTEC's two facilities in Massachusetts are close to our own operations.

"We are acquiring a very well run and profitable company.  We have the highest regard for the EBTEC team and welcome each of them to EDAC.  In addition to their engineering capabilities and design know-how, they share with the team at EDAC a deep and proven commitment to innovation and exacting execution, making both companies an ideal fit with each other."

EDAC Technologies Corporation is a diversified manufacturing company serving the aerospace and industrial markets.  In the aerospace sector, EDAC offers design and manufacturing services for commercial and military aircraft, in such areas as jet engine parts, special tooling, equipment, gauges and components used in the manufacture, assembly and inspection of jet engines.  Industrial applications include high-precision fixtures, gauges, dies and molds, as well as the design, manufacture and repair of precision spindles, which are an integral part of machine tools found in virtually every manufacturing environment. EDAC's core competencies include extensive in-house design and engineering capabilities, and facilities equipped with the latest enabling machine tools and manufacturing technologies.

For more information, visit: www.edactechnologies.com or www.ebteccorp.com

Wednesday, 23 May 2012 07:14

Launch of UP! mini 3d printer

Written by

Delta Micro Factory Corp. (PP3DP) announced today, the launch of the much anticipated follow-up, UP! Mini, to their highly acclaimed, flagship 3d printer, the UP! family. The all-new UP! Mini 3D Printer, with its full metal, temperature stabilizing enclosure and groundbreaking sub $1000 USD retail price, was introduced at simultaneous launches at RAPID 2012 in Atlanta, Georgia, USA, the Atlantic Design & Manufacturing Show in Philadelphia, Pennsylvania, USA, and CeBIT Australia in Sydney, Australia.

The UP! Mini is based on the simplicity of a traditional inkjet printer, with a snap in printer head, slide in build table and clip in consumable roll. You are ready to start making your big ideas into 3-Dimensional usable models out of tough ABS+ plastic.

There is no sacrifice on build quality with the UP! Mini, with its enclosed steel construction, double linear bearings on each axis and a temperature stabilizing build chamber; it is ready to produce quality parts on your desk within 15 minutes from switching it on.

"The UP! Mini is the result of 1000's of hours of field testing & valuable feedback from our rapidly growing UP!  user community." says PP3DP's Director of International Marketing, Joseph Guo.

Specifications:

  • Build footprint of 4.7” x 4.7” x 4.7” / 120 x 120 x 120mm with heated build table.
  • Enclosed chamber to reduce warping.
  • Double linear bearings on each axis - ensures consistent build quality throughout the entire print process.
  • Print speed of 9mins per cm3
  • Layer resolution of 250 microns
  • Chip free and open consumables – You can use any suppliers ABS roll of 1.75mm plastic with your UP! Mini. The UP! Mini consumable is an open design so you are not locked into expensive consumables as opposed to expensive inkjet cartridges.
  • USB interface for inkjet simplicity print spooling, you can unplug your computer once the UP! Mini starts printing.
  • Includes the Smart UP! Software, tools and a full roll of plastic to get you started.

With the introduction this week of the UP! Mini, PP3DP promises no compromises made when designing this newest member of the UP! family, "the Up! Mini has the features of the UP! Plus+ and is available, ready to print, for under $1000 USD. It is more suitable for family use." says Joseph Guo, "Not bad for a new born!"

UP! Mini will be available to preorder from June 1st from local resellers all over the world, and PP3DP website.

For more information, visit: www.pp3dp.com

Xten Industries, Kenosha, announced today that its subsidiary has acquired the assets of Paramount Plastics, LLC, Lockport, IL, an $18 million full service plastic injection molding company with special expertise in large-tonnage molding using engineered grade resins.  Paramount is an ISO/TS 16949:2002 certified company.

“We are very excited about the addition of Paramount, which greatly increases Xten’s production capabilities and substantially expands our customer base,” said Matthew Davidson, Xten CEO and Co-founder.

Founded in 1990, Paramount Plastics grew rapidly, establishing a solid reputation as a reliable large tonnage automotive supplier.  Within Paramount’s 122,000 square foot facility are 24 presses ranging from 60-2,000 tons, with shot capacities from 5 grams to 26 lbs.  A variety of robotic automation supports the production of parts sold into the industrial, consumer durable, health and fitness, automotive and packaging markets.

“In addition to the larger equipment, we’ve gained the operational expertise of Paramount’s people,” said Bill Renick, Xten’s president and operations leader.  “Out of the due diligence process, we came to realize how much they have contributed to Paramount’s success and feel fortunate to have them now within the Xten family.”

“One of the qualities both Xten and Paramount share is our dedication to providing exceptional service,” said Davidson.  “Given this common focus, we’re certain Paramount’s current customers will notice no decline in our ongoing support.”

Levin Ginsburg Attorneys at Law served as legal counsel to Xten Industries. Stevenson & Company advised Paramount Plastics and Chuhak & Tecson Attorneys at Law served as Paramount’s legal counsel.

For more information, visit: www.xtenindustries.com or www.paramountplastics.net

Cideas, Inc., leading Rapid Prototyping, Direct Digital Manufacturing (DDM) and 3D Printing company announced its acquisition of 3D Systems sPRO™ 60 HD HS. The purchase comes in response to growing demand for high definition prototypes and parts for aerospace, consumer products and medical industries.

"The sPRO™ 60 HD HS allows us to manufacture high-definition, durable plastic parts from a broad range of available thermoplastics," said Cideas President Mike Littrell. "What makes this a significant machine, is the digital scanning feature, a fairly new technology that is currently unavailable to the sPRO™ 140 and sPRO™ 230. "The part quality is extremely impressive; it enables us to create complex assemblies, as well as, production quantities with ease."

Cideas is the world's largest independently owned service provider of the Fused Deposition Modeling™ technology. Within months of relocating to their new state-of-the-art Chicago-land based facility, Cideas has installed two large frame Fortus Fused Deposition Modeling™ systems and one Selective Laser Sintering® system.

Cideas will display 3D printing technology, prototypes and parts at RAPID 2012, May 23-24, 2012. RAPID is North America's definitive additive manufacturing conference and exposition for design, prototyping, tooling and direct manufacturing technologies.

Founded in 1998, Cideas is the largest independently owned service provider of the Fused Deposition Modeling™ technology. Their new state of the art Chicago-land based facility was specifically designed to house their 16+ FDM™ systems, as well as; Selective Laser Sintering®, Polyjet™ systems, Urethane casting and Stereolithography® services. The new facility also boasts "in house" paint, polishing and pattern finishing services. Cideas supports over 10 different FDM materials such as: ABS-M30, M30i, ABS-ESD7, PC-ABS, PC-ISO, PC, ULTEM 9085, PPSF / PPSU, P400, and ABS F1. In addition to FDM™, the company offers an additional 15+ materials with Polyjet™, Selective Laser Sintering® (SLS®), Stereolithography® (SLA®), Urethane Casting, CAD Engineering and full model finishing services. Cideas is a member of the Additive Manufacturing Users Group (AMUG) and the Society of Manufacturing Engineers (SME).

For more information, visit: www.buildparts.com or www.production3dprinters.com/sls/spro-60-hd-sls-production-printer

During a customer event KraussMaffei showed fascinated trade visitors a new dimension of injection molding with the progressive GX series. Presented for the first time, the GX series extends the product portfolio in the segment of hydro-mechanical dual platen machines in the medium clamping force range. The passionate engineering of the developers is manifested in a first-class machine concept featuring intelligent product innovations such as the GearX locking device and the GuideX guide shoe. The GX series sets new standards in terms of performance, usability and value retention.

Visitors impressed by the exhibition with a demonstration of six machines

During today's world premiere in Munich, KraussMaffei provided a convincing demonstration of six machines in its new GX series with a clamping force ranging from 400 to 650 tonnes. These machines have different sizes and equipment variants for production requirements in a very large number of industries. The GX machines are impressive during the production of free falling packaging parts and premium quality articles for the automotive industry or the consumer goods sector. "Our customers were primarily interested in the modular automation cells containing linear and industrial robots in different configurations", summarized Dr. Karlheinz Bourdon, Vice President Technologies in the Injection Molding Machinery Segment of KraussMaffei, "and I can only emphasize that the GX is the best machine concept on the market!"

A powerful team: GearX and GuideX

The hydro-mechanical clamping unit in the GX series sets new standards in terms of quality and productivity. The excellent dual platen technology scores highly with a wide range of innovations. "In my opinion, the GX machines represent the best overall concept", underlined Bourdon. "We talk about a new dimension because our customers can use the machine to get the best results from their production." With the ingenious GuideX guide shoe, forces are ideally absorbed and the service life of the molds is increased. As an intelligent fixed bearing joint with an optimized FEM design, GuideX is not just an "eye-catcher", but a genuine highlight which ensures excellent platen parallelism due to the stable design and guarantees smooth, energy-saving movements. The innovative GearX locking system is reliably activated straightaway within the shortest possible time and continuously produces quick machine movements. Arranged in a space-saving way behind the moving mold fixing platen, it facilitates simple access and numerous customer-specific options.

Convenience and efficiency for the complete machine

Maximum priority is attached in the GX series to easy accessibility of the clamping, ejection and nozzle area, as well the switching cabinets and pump area. Thanks to the accessible design, the operator always works extremely comfortably and time efficiently. Short set-up times and simple maintenance are advantages that speak for themselves. GX: This is usability in a new dimension!

Powerful injection unit with proven plasticizing system

The proven KraussMaffei screw system, which ensures a wide range of applications, was retained in the GX series. Our standard plasticizing unit assures optimal melting quality and high throughput. “As a specialist for special polymers, we also offer our customers a raft of material-specific plasticizing solutions", said Frank Peters, Vice President Sales at KraussMaffei. “The application areas range from PC and PMMA through to PET, PC/PBT and plasticizing systems for long fiber processing." The Competence Center provides customers with competent advice, and there are hardly any limits to application areas. Fixed check valves with quick and precise closing behavior guarantee high weight constancy from shot to shot.

Processors profit from unlimited precision

The efficiency of the plasticizing process is supported by the proven in-line injection unit which has a rotary piston design and transmits force centrally via the injection piston to the screw. This direct path ensures absolute precision and maximum reproducibility Injection regulation of pressure and speed is a standard feature of the GX and guarantees processors maximum process reliability.

New MC6 control system offers considerable latitude

"With the MC6 we have a developed a control system which meets our customers' needs for "usability" in every respect”, said Bourdon. “It can be operated clearly and incredibly easy using SplitScreen and ProcessDesigner." Whether an operator is working with a KraussMaffei control system for the first time or is accustomed to its MC5 predecessor – MC6 technology is so intuitively accessible that he will hardly notice it. In keeping with our overall energy-efficient design, the MC6 control system has been equipped with a so-called "Eco button" for the first time. A most energetically optimum machine setting can therefore be made at the push of a button. The new "SplitScreen technology" shows the operator all important production processes at a glance. It almost never takes more than two clicks to get where you want to go quickly and easily. The integrated ProcessDesigner tool clearly presents all current processes in visual terms and enables you to modify them, depending on requirements, by means of simple drag-and-drop movements or wiping movements. This is also usability in a new dimension.

Overall modular concept creates flexibility

No matter which injection unit, clamping unit or drive is needed, the modular machine design makes it possible to meet every individual requirement. Due to the fact that the machine center always remains at the same height, the system is compatible with all clamping and injection unit combinations. In the modular drive system of the GX series, the latest generation of the variable delivery pumps is a standard feature. Their use improves efficiency and guarantees processors maximum cost-effectiveness. The parallel movement of the ejector and core pullers increases productivity and is integrated in the standard. The new premium quality hydraulic components were designed with the focus on higher availability and a long service life to meet the latest state of the art regarding energy efficiency. Depending on the application and production cycle, the machines can be supplied with different PowerPack performance classes for first-class economical production. Through the optional use of "Blue Power Servo Drive" Technology, energy consumption is further optimized compared with variable delivery pumps. The saving amounts to 10 and 30 percent depending on the particular application. Compared with conventional hydraulic concepts on the market, savings of up to 50 percent are actually possible.

Perfect symbiosis of automation technology and machine

Even with fully integrated overall systems comprising a machine and automation technology, KraussMaffei goes one step further. Machine and handling form a functional unit in this combination. The linear robots from the LRX series are ideally suited for simple pick & place solutions and quick removal. The industrial robot (IR) guarantees maximum flexibility during complex demolding and a wide range of other assembly steps or production steps. A uniform protective housing makes the perfect symbiosis visible on the outside as well. The shared control MC6 system in particular represents true added value for the customer. It allows both functional units - machine and automation - to be controlled on any control panel: Smart programming with WizardX: The dialog-based programming assistant in the MC6 control system allows even beginners to create basic demolding processes in the shortest possible time. The interactive communication between the user and control system makes manual programming superfluous and eliminates programming errors.

Impressive during first-time use in production

A GX 550-4300 was delivered to WAFA Kunststofftechnik GmbH in Augsburg in October 2011. Due to the very high demands on the production process and the component, the company was deliberately selected for the field tests in continuous production operation. "The high precision, speed, modularity and high usability completely convinced us", said Wolfgang K. Müller, proprietor and managing director of WAFA. "KraussMaffei once again raised the bar for the high quality of their injection molding machines with their new GX series." The machine is equipped with a type LRX 250 linear robot, the basic component for economical manufacturing cells. This removes the sensitive parts, places them on a cooling/conveyor section and separates the sprues gates as required. The robot also ensures that conditions regarding demolding time and cycle time remain consistent, thus exerting a positive influence on process conditions. "KraussMaffei has created a top-quality machine with the GX, which literally opens up new dimensions. The modular design, high performance and outstanding precision combine to form one user-friendly machine - a great performance!", said Wolfgang K. Müller praising the development team.

For more information, visit: www.kraussmaffei.com

3D Engineering Solutions employed 3D laser scanning, structured light scanning and Geometric Dimensioning and Tolerancing (GD&T) best practices to reverse engineer components for military aircraft, including parts for large helicopters and Harrier jump jets recently sold by Britain to the U.S. Because the CAD models and prints for these parts are not available, 3D Engineering digitized each component, determined the materials, finishes and coatings, and then created new CAD models and prints to be used by government suppliers in recreating each piece. 3D laser scanning was employed to digitize the larger parts while structured light scanning was used to capture the smaller, detailed components.

“The difficulty in these types of projects comes in discerning the original design intent of the component. This is done by studying how the parts interact with the overall system and applying proper dimensioning and geometric dimensioning and tolerancing (GD&T) that is appropriate for the design intent and to reduce the end cost of the components,” said 3D Engineering Solutions Vice President of Operations Rob Glassburn, P.E. In all, 3D Engineering created over 200 prints for the helicopter and Harrier projects, comparing the scans they captured with the models they created numerous times.

3D Engineering Solutions is completing the prints of these wear item components at a time when Diminishing Manufacturing Sources and Material Shortages (DMSMS) pertaining to military aircraft is on the rise. “For various reasons, suppliers to our government are no longer able to provide key components to certain systems. Many of these components are wear items that need to be replaced on a frequent basis,” said Glassburn. “When the prints for these parts aren’t available, that’s where we come in.”

Customers rely on 3D Engineering Solutions to design process tooling and fixtures for the automotive, industrial, green energy, nuclear and aerospace industries, using engineering tools such as Siemens advanced NX7.5 Mach 3 CAD platform. Leading edge point cloud software, InnovMetrics PolyWorks, allows a common software platform for collecting data across all of Faro laser-based data collection platforms. In addition to reverse engineering services, 3D Engineering Solutions is registered with the State of Ohio for Professional Engineering and ISO 17025 Certified for third party inspection. In their seventh year of operation, the company maintains a state-of-the-art, climate controlled metrology lab, servicing the Midwest OEM needs for 3D laser scanning, data collection, 3D CAD modeling, FAI / PPAP inspection, and reverse engineering services. 3D Engineering Solutions brings more than 100 years of collective experience to every engineering project.

For more information, visit: www.3D-engineering.net

3DVision Technologies is thrilled to announce the launch of its brand-new website.

According to Carrie Patrick, Marketing Manager for 3DVision, there were several goals in mind when redesigning the site. "In our business, the technology is constantly changing. We found ourselves unable to make quick changes and updates to our site to better communicate our products and services to our customers. With this new platform and site redesign we are now able to make updates within hours, not days."

3DVision Technologies last launched a complete site redesign in 2009. While the site was current and still relevant, Patrick believed that it was time to take things to the next level.

With a clean look and new information geared specifically toward 3DVision's technologically minded audience, the site is engaging and educational, holding the user's interest and providing a format that is easy to navigate.

Todd Majeski, President and CEO of 3DVision Technologies, noted, "From a visual standpoint, the new site really reflects our company brand as well as the brand of our partners. In addition we are now able to more effectively communicate with our customers and potential prospects."

Patrick notes, "No matter what your size, your company website leaves a lasting impression with any visitor. At 3DVision Technologies we believe that we have once again differentiated ourselves from our competition and this is just the beginning."

3DVision Technologies Corp. is the leading value-added reseller of SolidWorks 3D CAD software in Ohio, Kentucky, and Indiana. At 3DVision Technologies, our team of experienced engineers and world-class trainers help our colleagues in the design and manufacturing industries produce high quality products in less time with lower costs. Our products, including 3D solid-modeling, computer aided analysis, and product data management, provide the tools you need to rapidly turn your ideas into business success.

For more information, visit: www.3dvision.com

Lincoln Electric Holdings, Inc. (Nasdaq: LECO) announced today that it has acquired Wayne Trail Technologies, Inc., a privately held Ohio-based manufacturer of automated systems and tooling, serving a wide range of applications in the metal processing market.

"The addition of Wayne Trail Technologies strengthens our already strong position as a market leader in welding automation in North America," said John M. Stropki, Chairman and Chief Executive Officer. "Wayne Trail brings extensive design and system building experience, and we are particularly excited about the company's proven capabilities and continued commercial success in the area of laser welding systems."

"We look forward to expanding our ability to serve customers in the U.S. and international markets as part of Lincoln's broad portfolio of welding and automated solutions for its global customer base," said David M. Knapke, President and CEO of Wayne Trail Technologies.

Wayne Trail Technologies, Inc., with headquarters and manufacturing operations in Ft. Loramie, Ohio, has annual sales of approximately $50 million and employs 162 people.

Terms were not disclosed.

Lincoln Electric is the world leader in the design, development and manufacture of arc welding products, robotic arc welding systems, plasma and oxyfuel cutting equipment and has a leading global position in the brazing and soldering alloys market. Headquartered in Cleveland, Ohio, Lincoln has 45 manufacturing locations, including operations and joint ventures in 20 countries and a worldwide network of distributors and sales offices covering more than 160 countries.

For more information, visit: www.lincolnelectric.com

Like other professionals, architects have used computer-aided design (CAD) software in their work for decades. Typically, the resulting digital files are converted to hard-copy plans, which are then used to support traditional construction practices.

Researchers in the College of Architecture at the Georgia Institute of Technology are now automating some of the processes by which computer-based designs are turned into real world entities. They're developing techniques that fabricate building elements directly from digital designs, allowing custom concrete components to be manufactured rapidly and at low cost.

"We're developing the research and the protocols to manufacture high-end customized architectural products economically, safely and with environmental responsibility," said Tristan Al-Haddad, an assistant professor in the College of Architecture who is a leader in this effort. "We think this work offers opportunities for architectural creativity at a new level and with tremendously increased efficiency."

In one recent project, Al-Haddad and a College of Architecture team collaborated with Lafarge North America to fabricate an award-winning building-element concept called a "Liquid Wall." The Georgia Tech team employed digital techniques to help construct a prototype wall, using ultra high-performance concrete; the result was displayed by the New York Chapter of the American Institute of Architects (AIANY) in the "Innovate:Integrate" exhibition.

In another Lafarge-sponsored project, Al-Haddad and a College of Architecture team are developing a complete free-standing structure using ultra high-performance concrete elements fabricated directly from digital designs.

The Liquid Wall, originated by Peter Arbour of Paris-based RFR Consulting Engineers, won the 2010 Open Call for Innovative Curtain-Wall Design competition conducted by the AIA. The concept advanced a novel approach to curtain walls, which are building coverings that keep out weather but are non-structural and lightweight.

RFR's plans called for the Liquid Wall to be constructed of stainless steel and Ductal®, a light and strong ultra-high-performance concrete (UHPC) that is produced by Lafarge. Moreover, the new building enclosure was conceived as an entire system, including integrated louver systems, solar shading, integrated passive solar collectors and other advanced features.

Georgia Tech became involved in the Liquid Wall project when RFR decided to built a full-scale prototype of the complex concept. RFR asked Al-Haddad to help turn Arbour's original parametric sketches into a manufacturable design.

Supported by the College of Architecture's Digital Building and Digital Fabrication laboratories, the researchers refined the geometry of the original sketches for manufacturability and developed the techniques required for fabricating a full-size curtain wall.

Then, working from their digital models and using a five-axis CNC router – a device capable of machining material directly from a digital design – the Georgia Tech team milled a full-scale model of the wall. The model was made from a lightweight polymer material, expanded polystyrene (EPS) closed-cell foam, which was then given a polyurea coating.

The digitally milled foam model created an exact replica – a positive -- of the final wall. The lightweight positive could then be used to produce a negative capable of forming the actual prototype. In this case, the collaborators used the positive to produce a rubber mold – the negative – from which the final wall was cast.

The foam positive was shipped to Coreslab Structures Inc., a large corporation that specializes in industrial-scale casting. The Georgia Tech team then worked with Coreslab to identify the best techniques for creating the rubber mold and for pouring in Ductal to form the concrete wall.

"It was a very collaborative process – the four major players were Peter Arbour and RFR, Georgia Tech, Coreslab and Lafarge," Al-Haddad said. "And we had all of three weeks to finish the work before the exhibition deadline – so it was pretty intense."

Other College of Architecture people involved in the collaboration included graduate student Andres Cavieres, associate professor Russell Gentry and professor Charles Eastman, director of the Digital Building Laboratory. The resulting full-size Liquid Wall prototype was installed at the Center for Architecture in New York City as part of the AIANY's "Innovate: Integrate" exhibition, and was on view for several months in 2010 and 2011.

The Liquid Wall project was challenging, said Eastman, who holds joint appointments in the College of Architecture and the College of Computing. The process involved not only producing rubber negatives using wall-form designs created with CAD and parametric-modeling software, but also required identifying the right production procedures and finding effective ways of installing a completed full-size wall on a building.

"When you're creating a completely new process like the Liquid Wall, you're faced with developing a whole new manufacturing process for this kind of material," Eastman said.

A future project, expected to be about 20 by 20 feet square and 15 feet high, will be built using Ductal UHPC, principally or entirely. A central technical challenge will involve molding the many custom elements so that all edges fit together and form a structure that is stable, practical and esthetically pleasing.

"We understand the structural side of a project like this quite well -- the difficulty comes in the actual manufacturing of the elements," Al-Haddad said. "We want to advance the use of digital parametric models with custom molding systems, and create a free-form manufacturing system that can produce many variations quickly and accurately."

For more information, visit: www.dbl.gatech.edu/dfl/liquid-wall

Monday, 14 May 2012 11:16

SURFCAM 6 Beta Released

Written by

Surfware, Inc. announced this week that the beta version of its flagship CAM software, SURFCAM 6, has been completed and is being made available to SURFCAM Beta Users, Testers and Resellers worldwide.

SURFCAM 6, the next major up and coming release, is on schedule to follow the previous SURFCAM V5 Series of releases. SURFCAM V5.2 was released in April 2011, SURFCAM V5.1 was released in September 2010. The SURFCAM V5 Series was launched in February 2010 starting with the introduction of SURFCAM V5.0.

“SURFCAM 6 is a significant release version for any serious CAM programmer,” says Peter Marton, Vice President of Surfware. “A large part of this release has been dedicated to taking the existing power and control available in the software today and coupling it with enhancements and features to make for an improved user experience. The addition of a 64 bit version, new and updated internal technologies, and even many new additional features and enhancements will prove this version of SURFCAM 6 to be a must for all programmers that require a tool which is easy to use while allowing programmers the ability to create toolpaths with utmost precision and control. With all the capabilities now available in our flagship product, SURFCAM 6 still remains one of the most competitively priced CAD/CAM systems in the market today.”

Some of the new features and enhancements available in SURFCAM 6 are:

  • A 64-Bit Version
  • New Tools and Material Database Engine
  • Faster and Improved Verification Technology
  • Updated Interface
  • Completely redesigned Help System
  • Four (4) new toolpath strategies
  • Updated CAD translators (plus RHINO CAD translator now included)
  • Updated and New Post Processors (MPost and SPost)
  • New Productivity Utilities
  • Updated Digitizer Interfaces
  • New versions of editNC and SDNC
  • Enhanced TRUEMill toolpath calculator and toolpath algorithms
  • ...Plus much more

"We have found this beta release of SURFCAM 6 to be solid and stable,” says SURFCAM Reseller Don McKillop in Florida. “I am really pleased with all the behind the scenes work put into this version to bring it to the competitive state it is in today. We have all the power in SURFCAM 6 to easily create the most complex of 5-Axis toolpaths, and then making them work on the floor seamlessly with the post processors we support.”

"This version is a nice mix of features and 'stable under the hood' type work," says SURFCAM Reseller Greg Martin in Utah. "Surfware has really demonstrated their commitment to SURFCAM CAD/CAM systems competitiveness and set the stage for many years to come with new feature-rich development. We look forward to getting this release in the hands of all of our many SURFCAM customers."

For more information, visit: www.surfware.com

When manufacturing products, the coating technology is a key innovation driver for almost all areas of daily life – for example, for making scratch-proof displays for smart phones or anti-bacterial surfaces in refrigerators. Other coatings protect components from corrosion or aging, for example in a solar cell module or a car engine, without the end user noticing their existence. In industry today, wet chemical processes or vacuum plasma processes are primarily used for coating applications. Both have drawbacks. Vacuum units are expensive, limited to smaller components and applying a coating takes a relatively long time. Wet chemical processes often involve high resource and energy consumption with the corresponding environmental damage and can also cause difficulties in the handling of material combinations for lightweight construction such as plastics/ metals or aluminum/steel.

“There has to be another way”, thought Dr. Jörg Ihde and Dr. Uwe Lommatzsch from the Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM in Bremen. Together with Plasmatreat GmbH, the IFAM team developed a new kind of plasma coating process that works at ambient pressure, that is to say, in an open atmosphere. “And that poses a major challenge”, explains Jörg Ihde. “Because the pressure is more than 10,000 times higher and the absence of a vacuum reactor, we had to stop unwanted particles from forming and embedding in the coating. That was the key to developing robust and efficient industrial processes using the new plasma system.

One nozzle – various functional coatings

The central element is a plasma nozzle. The nozzle is no bigger than a typical spray can. Yet it contains a highly complex coating system. “In the nozzle, an electrical discharge generates small flashes - a plasma that is expelled from the nozzle in the form of a jet. We systematically feed into the nozzle outlet those materials that are excited and fragmented in the plasma and then deposited out of the plasma jet as a functional nano-layer onto the surface”, explains Uwe Lommatzsch. “We achieve extremely high deposition rates, enabling fast and cost-effective production processes to be realized.”

The use of a nozzle allows the coating to be applied very precisely and only where it is needed, thus conserving resources. “We can control the processes so that the same nozzle can be used to apply coatings with various functionalities, for corrosion protection or for increasing or reducing adhesion, for instance”, adds Jörg Ihde. Only very small amounts of coating material are required and practically all materials and material combinations can be coated. The process offers, in addition to the coating qualities and functionalities, even more benefits: it can be easily integrated into an inline production process, requires little space and is easy to automate, meaning it can be controlled via a robot. Yet another advantage: low investment costs and easy on the environment. The positive characteristics benefit industrial production: depositing an adhesion-promoting coating on a car window edge before gluing it in, to replace environmentally damaging chemicals or as a substitute for thick protective paint on printed circuit boards, which improves heat dissipation and hence prolongs service life. The process is already employed in the automotive industry and the energy sector to provide protection against corrosion and aging.

For more information, visit: www.fraunhofer.de/en.html

Ashok Agrawal, M.S., P.E., vice president for Academic Affairs at St. Louis Community College - Florissant Valley, Ferguson, Mo., and a member of the SME Education Foundation Board of Directors, has been acknowledged as a leader exemplifying the best in engineering and engineering technology education by The American Society for Engineering Education (ASEE), and awarded the prestigious James H. McGraw Award.

Ashok Agrawal has served engineering and engineering technology and has held every professorial and administrative position from instructor to chief academic officer. He established the Emerson Center for Engineering and Manufacturing. As a Program Officer of the National Science Foundation (NSF), he played key roles in expanding the Advanced Technological Education program and increasing the visibility of STEM (Science, Technology, Engineering and Mathematics). An ASEE Fellow and Frederick J. Berger Award recipient, he served ASEE in numerous offices of the Engineering Technology Council and Division, and on the Technology Accreditation Commission of ABET.

Agrawal will be honored at the ASEE Awards Banquet being held at the Henry B. Gonzales Convention Center, Ballroom C – 7:30 p.m. – 10 p.m., on Wednesday, June 13, 2012. Recipients of 15 ASEE national awards will be honored at the Banquet, in addition to 11 Fellows. Agrawal will receive a $1,000 honorarium award and certificate. The awards ceremony will be held during the 119th ASEE Annual Conference & Exposition in San Antonio, Texas, June 10-13, 2012.  

Agrawal holds an MS degree in Materials Science, an MS degree in Mining Engineering from the University of Kentucky, and a BS degree in Metallurgical Engineering from Nagpur University in India. Before joining St. Louis Community College, Agrawal was a tenured Associate Professor and Chair of the Department of Engineering Technology at West Virginia Institute of Technology.

Prior to assuming his present position as vice President for Academic Affairs, Ashok Agrawal was the dean of the Math, Science, Engineering, and Technology Division and responsible for leading and administering its transfer and career programs. His efforts led to the establishment of the Emerson Center for Engineering and Manufacturing, the development of the joint 2+2 Bachelor’s degree program with Southeast Missouri State, and creation of several customized training programs for key regional corporations including Ameren, AT&T, and Boeing.

As director of the Emerson Center, Agrawal actively engages with St. Louis Community College’s Workforce and Community Development, St. Louis County Economic Council, and the St. Louis Regional Chamber and Growth Association (RCGA).

In 2006, he was selected to participate in Leadership St. Louis® (LSL), one of the most highly-respected leadership development programs in the nation. The program was built on the belief that the community, just as any business organization, requires strong leadership to grow and improve. In the same year, he was appointed by the Governor of Missouri to serve on the Missouri Math, Engineering, Technology, and Science (Mo-METS) task force, and serve with the Mo-METS coalition. He also serves on the planning team of the St. Louis Region’s FIRST Robotics Competition and on the advisory committee of the St. Louis Science Center.

Agrawal has been honored with numerous awards and recognitions. He is the recipient of the 2003 Florissant Valley David L. Underwood Lecture Award, and also the Governor’s Award for Excellence in Teaching. Agrawal and his colleagues led the effort to establish a St. Louis Regional Engineering Academy for St. Louis area schools, which included the implementation of Project Lead The Way engineering curriculum. He has received several grants from the National Science Foundation (NSF), and other public and private agencies, including a grant for the College Career Transition Initiative from the League of Innovation.

He has served as a Program Officer at the Division of Undergraduate Education at the National Science Foundation, and continues to assist NSF on special projects. Agrawal has also served on the National Academy of Engineering (NAE) Committee to Advance Engineering Studies at Tribal Colleges, the NAE Committee on Community Colleges Role in Engineering and Education, and the National Research Council (NRC) Board on Engineering Education.

Ashok Agrawal is also involved in international activities collaborating with Georgetown University to coordinate The Cooperative Association of States for Scholarships (CASS) program which provides technical training and professional training for low-income and rural students from the Dominican Republic, El Salvador, Guatemala, Haiti, Honduras, Mexico, and Nicaragua;  and The Scholarships for Education and Economic Development (USAID SEED) Program, which is funded by the United States Agency for International Development (USAID) and administered by Georgetown University’s Center for Intercultural Education and Development (CIED).

Founded in 1893, the American Society for Engineering Education is a nonprofit organization of individuals and institutions committed to furthering education in engineering and engineering technology. In pursuit of academic excellence, ASEE develops policies and programs that enhance professional opportunities for engineering faculty members, and promotes activities that support increased student enrollments in engineering and engineering technology colleges and universities.

For more information, visit: www.asee.org

Die & Mold China 2012 (DMC2012) will be held in Hall E1-E6 at the Shanghai New International Expo Centre from May 31st to June 3rd. This year's exhibition will highlight the salient characteristics of new technologies, new processes and new structures, with high-end manufacturing and innovation as priorities for exhibitions and themes of presentations.

Fifteen hundred exhibitors from 15 countries and regions, including Germany, Switzerland, Japan and Korea, are slated to participate in the event and showcase their new products and technologies.

A group including over 30 domestic die and mold makers from Guangdong and Zhejiang provinces that form the elite of China's contribution to the sector will jointly demonstrate the unique elements that sets them apart.

Several other conferences, including an industry summit led by China Die and Mold Industry Association (CDMIA), a technology seminar organized by SWISSMEM (the Swiss association of mechanical and electrical engineering industries) in concert with several international organizations, as well as many market-focused events held by BOSCH, other world-leading firms, and several users associations, are scheduled to take place concurrently.

"Offshore Wind China 2012", which is being held at the same time in a nearby venue, will complement DMC2012 in terms of synergies all along the new energy sector's production chain.

The exhibition's crowning event will be the gathering of the industry's leading decision makers and influencers from both within China and abroad where they plan to discuss cutting edge technologies and the demand for large-scale and high-end equipment, driving the transformation and evolution of the sector.

For more information, visit: www.dmcexpo.com/en/Default.aspx

Philadelphia University will name its innovative interdisciplinary college for alumnus Maurice Kanbar '52, H'03, who has donated $15 million in support of the Kanbar College of Design, Engineering and Commerce. The $15 million gift is the largest in Philadelphia University history.

"It is with great pride and gratitude that we accept this generous gift from our esteemed alumnus and benefactor Maurice Kanbar," said Philadelphia University President Stephen Spinelli Jr., Ph.D. "Mr. Kanbar's investment in this University is a testament to his belief in our vision, and in the strength and talent of our faculty and students. This is a transformational gift in support of a transformational academic experience."

Kanbar, an entrepreneur, inventor, Hollywood producer and philanthropist, said the Kanbar College of Design, Engineering and Commerce, with its focus on transdisciplinary learning and identifying and solving real-world problems, will enable students to achieve success in the 21st century work place and contribute to society.

"The College will be of tremendous benefit to students, and make it easier for them to succeed in life," Kanbar said. "The number one rule to follow is never be happy with the way things are, always be thinking about how to make it better," he said. "That is basically what I have done my whole life."

"Through the convergence of the design, engineering and business disciplines and connections with industry partners, the College of Design, Engineering and Commerce pushes students to think beyond the boundaries of existing academic fields," said Philadelphia University Provost Randy Swearer, Ph.D. "This College, coupled with our Nexus Learning approach, is helping Philadelphia University to revolutionize higher education. Mr. Kanbar's significant contribution is a vital factor in achieving our vision of being the model for professional university education in the 21st century."

The Kanbar College, which officially launched in fall 2011, offers students an integrated educational experience that prepares them to think critically about the world, giving them a multi-dimensional understanding of their rapidly evolving fields.

"A hallmark of the Kanbar College requires that all students participate in an integrated core curriculum beginning on the first day of their freshmen year," said Ronald Kander, Ph.D., executive dean of Kanbar College. "Through our unique curriculum, students learn to ask the right questions, identify problems, deal with complex issues, create opportunities and innovate.  They gain mastery of their specific disciplines along with the added value of expertise in related fields, thus giving them a competitive edge in the workplace."

To support the College's innovative curriculum, Philadelphia University is constructing a new building, set to open in January 2013, which will include flexible space for studios, seminars, conference meetings and team projects, allowing teaching and work space to be reconfigurable as projects and curricula evolve. The 38,500-square-foot building, built to LEED standards, will reinforce the College's integrated curriculum that pushes students to think beyond the boundaries of existing disciplines and focus on market-driven innovation through teamwork, collaboration and industry connections.

In addition to his latest donation, Kanbar gave $6 million for The Kanbar Campus Center, which opened in fall 2006. His support of Philadelphia University and other academic programs stems from a deep-seated belief in the transformative power of education. "Without an education a person is lost," he said.  "With an education a person has a chance. With a good education, a person has a better chance."

In 2003, Philadelphia University awarded Kanbar, who invented SKYY Vodka, the D-Fuzz-It sweater comb and produced several films (including the animated movie Hoodwinked), the honorary degree Doctor of Humane Letters.

Philadelphia University, founded in 1884, is a private university with 3,600 students enrolled in more than 60 undergraduate and graduate programs.  As the model for professional university education, the University prepares students to be leaders in their professions in an active, collaborative and real-world learning environment infused with the liberal arts.  Philadelphia University includes the innovative Kanbar College of Design, Engineering and Commerce; the College of Architecture and the Built Environment; and the College of Science, Health and the Liberal Arts.

For more information, visit: www.philau.edu/designengineeringandcommerce/index.html

Start
Prev
1
Page 1 of 19

Copyright © 2014 Prototype Today ®. All rights reserved.

|   Privacy Policy   |   Terms & Conditions   |   About Us   |   Contact Us   |

All trademarks and registered trademarks are the property of their respective owners.